Search Documents

By Cyril Smith

A STUDY of the precipitation-hardening of copper steels1 led the authors to investigate malleable iron containing copper, for the low-carbon ferritic matrix in malleable iron should lend itself admirably to precipitation-hardening. It was soon found that in addition to rendering malleable iron susceptible to improvement by precipitation-hardening treatments, copper has another potentially useful effect as an accelerator of graphitization. Brief mention of these effects was given in a general paper by Lorig and one of the present authors2; the present paper gives further details on the graphitization and precipitation-hardening effects only. After the completion of this work a paper by L. Lykkin3 appeared, confirming the authors' conclusions regarding graphitization.

Jan 1, 1935

By Clarence O. Babcock

A simple robust rock bolt load gage was tested in the laboratory to define its characteristic behavior and to obtain a measure of its performance. The gage uses three vibrating wire sensors crimped 120 (2.09 rad) apart into the outer surface of a hollow cylindrical steel, tube. The resonant frequencies of the wires change as the gage is loaded. This change is read with a Creare meter developed for the Bureau of Mines on a previous contract to read borehole stress gage results. A statistical analysis of data obtained defines the variables influencing results. A U.S. patent (3,914,992) assigned by the author to the Dept. of the Interior was granted Oct. 28, 1975.

Jan 1, 1978

By A. Boltax

H. Herman and M. E. Fine (Northzcesteriz University)—The author is to be complimented on the quality and completeness of his work. Of special interest to us was the exponent of time in the exponential rate equation, n = 0.28 ± 0.03, since it is consistent with results for the early stage of quench-aging in A1-2 at. pct Cu, n = 1/3, first determined in this laboratory."' In that work we attributed the early kinetics to attraction of vacancy - solute atom complexes to the plate-shaped zone due to the strain field about the zone and the lowering in free energy. To our knowledge, Hirano et 1.' were the first to

Jan 1, 1962

By R. R. Nash, W. F. Sheely, E. D. Levine

ThiS note reports on the variation with temperature of critical stress for basal slip of binary solid-solution single crystals of indium and of thorium in magnesium. PROCEDURE Alloy single crystal spheres were acid machined to 3/8-in. diam cylinders with the basal planes of the crystals normal to the cylinder axis and then annealed at 810°K. Stress was applied parallel to the slip system, (0001) [1120]. Experimental details will be presented in another paper.' Two nearly equivalent' techniques of stressing were used. Stress on the magnesium-indium alloy crystals was increased by 1 g per sq mm at 1-min intervals, and the critical flow stress was defined as the lowest stress to pro-

Jan 1, 1960

By S. N. Dixon

Sampling and assaying procedures were developed to obtain unbiased and reasonably accurate Au grade estimates in drill samples fm a coarse gold deposit. Gold grade comparisons were made by assaying 3 (1 assay ton) splits from each drill interval, then processing the entire reject thru a pilot plant for a blocked out zone. The result comparing the assay splits to the pilot plant results gave a ratio of 1 to 1.07. Another technique was developed to detect drill samples which has a coarse gold content by monitoring the varience. Testwork could be done on a 1 kg sample to improve the accuracy of the grade estimation if the variance was high for a drill interval.

Jan 1, 1984

By M. N. Nabighian, J. R. Odekirk, D. M. Hausen

Preliminary investigations based on the concept of cross-power indicate that quantitative volume percentages of minerals, including quartz, orthoclase, plagioclase, fluorite, and chalcopyrite can be obtained by X-ray diffraction analysis. Pulverized samples are scanned from 4° to 65°, 2e, using a Norelco diffractometer, with the output recorded on a punched tape at 40 intervals per degree, 29. Errors from crystal orientation are minimized by (1) gridded surface packing, (2) sample spinning, and (3) quantitative measurement of all major diffraction peaks. Computer programming enables rapid quantitative evaluation of X-ray diffraction data. Results to date indicate that most minerals analyses can be performed within an accuracy of ±2%. Metallurgical applications include analysis of various flotation concentrates and tailings.

Jan 1, 1973

By R. D. Caudle, Yoginder P. Chugh, V. K. Agarwala

Longwall coal mining is a growing mining technique in the United States. However, very little premining exploration data are collected presently by coal companies to 1) select coal winning equipment, 2) select and design face supports and supports in gate and tail entries, or 3) optimize operational parameters such as length, width, and orientation of face. The authors are of the opinion that much of the data needed for mine planning and design for longwall mining can be obtained during exploration. In this paper, the authors identify the data requirements, discuss how these data can be obtained during exploration, propose an exploration program and estimate the cost to obtain the necessary data.

Jan 1, 1982

By W. M. Duncan, F. S. Kendorski, C. V. Jude

After shotcrete had been in use for a short time al the Climax Mine of the Climax Molybdenum Co., Climax, Colo., it was noted that regular longhole undercutting blasts would severely damage or detach slusher drift shotcrete linings. If this were to be a usual occurrence, the widespread application of shotcrete would have to be reexamined or abandoned. Concrete drift linings are affected less by blasting because of occasional significant gaps between the placed concrete and rock and the greater thickness of poured-in-place linings. Research Project Organized A research project was organized to determine: 1) the seriousness of the problem, 2) more complete in-use shotcrete strength data, and 3) possible solutions.

Jan 12, 1973

By H. R. Hardy

The study of the mechanical properties of geologic materials was initiated in the Mining Research Section of the Fuels and Mining Practice Division in 1951 as part of a fundamental study of ground stress in Canadian coal mines.1 Early in the investigation of the mechanical properties of geologic materials, however, it was realized that the test results are influenced by the rate and the duration of loading. For this reason, laboratory investigations2,3 were undertaken to study the effect of long-period uniaxial stress on the deformation and failure properties of these materials. A literature survey indicated that work on the time-dependent properties of geologic materials had been very limited in the past.

Jan 1, 1965

By W. L. McMorris, Shiou-Chuan Sun

The Convertol process was first described in Ger- many by Muschenborn1 in 1952. In the U. S. Fraser2 reported this new process in 1953, and Brisse and McMorris-resented the results of a Convertol pilot plant at the Alpheus preparation plant in Gary, W. Va., illustrating the mechanics of the process by a series of sketches. The purpose of the present investigation was threefold: 1) to determine the relative effectiveness of various oils and hydrocarbons for recovering coal by the Convertol process, 2) to ascertain the behavior of coal pulps in this process under various operational conditions, and 3) to compare Convertol with flotation in the recovery of fine coals.

Jan 11, 1959

By Jack White, Ralph B. Adair

THE Mufulira mine in Northern Rhodesia is 13° south of the Equator and at an altitude of 4100 ft above sea level. The concentrator was planned in 1930 to treat about 10,000 tons of ore per day, but before construction work had gone very far the size of the plant was reduced to 1500 tons daily capacity. Then just as the construction was finished in December 1931, the price of copper did not warrant the commencement of operations and it was not until October 1933 that the mine re-opened. Extensions have been made to the plant in 1034, 1935, 1936 1937, 1940 and finally in 1945. The capacity of the plant when the 1945 extension is completed will be 9500 short tons per day. The various extensions have been carried out with the minimum confusion and with great skill on the part of the designers and the erection engineers. In dealing with the plant in this paper it is proposed to give an outline of the present practice and only to refer to past practice when it is considered of particular interest. ORE TREATED The ore consists of fine grained highly siliceous, felspathic and argillaceous quartzites, the latter containing graphitic carbon and locally termed graywacke. These rocks are considerably altered near the surface and on the fringes of the ore body. Despite extensive efforts at mixing, both underground and in the crushing plant, many sudden changes of ore take place in the mill feed. The minerals are chalcocite, bornite and chalcopyrite with relatively unimportant amounts of malachite, native copper, azurite, covellite and chrysocolla. Gold is present at about 1 oz to a thousand tons, and silver at about 2 dwt. per ton. With increasing depth the nonsulphide content or, as commonly termed locally, the oxide content of the ore is decreasing and is now less than 0.25 pct against a high of 0.77 pct. CRUSHING OPERATIONS The first stage of crushing is done underground where the oversize from 12-in. grizzleys is fed to a 56 X 72-in. jaw crusher. At the Selkirk shaft two 10-ton skips deliver the run of mine ore at a rate of 450 tons per hour to the 400-ton capacity shaft bins. One 6 ft wide Ross chain feeder and one locally made air-operated finger feeder feed the two 30-in. McCully crushers. Ahead of each crusher is a 6 X 9-ft spring grizzley spaced at 5 in. on a 35° slope. Neither the Ross chain feeder nor the finger feeder is entirely satisfactory and for the wet, muddy and sticky ore that has to be handled it is planned to replace these with two 6-ft wide apron pan feeders. The McCully crushers deliver a minus 5-in. product, at a rate of over 500 tons per

Jan 1, 1947

Speech advocating a new law of the sea-the "common heritage of mankind." The 3rd Law of the Sea (L0S) Conference was held in Caracas in mid-1974, and a fourth UN conference, scheduled for mid-March in Geneva, will once again attempt to produce a cohesive LOS Convention to take up where the 1958 Geneva Convention left off. The 1958 Convention specified coastal state resource rights on a continental shelf out to a water depth of 200 m-a supposed technological limitation at the time. But the surge of offshore petroleum drilling and the advent of the nodule resource have long since exploded beyond the 200-m limit.

Jan 4, 1975

By C. Ernest Birchenall

TWO recent papers1,2 cite measurements of surface contour changes on copper which, when attributed to surface self-diffusion, can be interpreted to yield activation energies for surface self-diffusion that approach1 or exceed2 those reported for volume self-diffusion in the same metal.3 It is acknowledged2 that AS must be assigned much too large a value to be physically reasonable in order to make the theoretical Do's agree with the experimental values, if the jump distance is of the order of the interatomic distance. However, long jumps would probably lead to marked anisotropy on planes that consist of ridges and valleys (like (110) in fcc) whereas only mild

Jan 1, 1963

The Mining Enforcement and Safety Administration has called attention to the increasing frequency of accidents occurring during mine maintenance and repair tasks in a recent publication. Data from the agency's Health and Safety Analysis Center have been compiled and presented in a report titled "Analysis of Injuries Associated with Maintenance and Repair in Metal and Nonmetal Mines,"* a booklet aimed at answering four questions: (1) Which pieces of operating equipment are most frequently involved in maintenance accidents; (2) Which maintenance functions are the most hazardous; (3) Which tools are most often associated with injuries; and (4) What is the comparative hazard of welding or flame cutting vs. mechanical or electrical maintenance functions.

Jan 3, 1978

By Richard R. Zupp, David A. Stevenson

A theoretical treatment of austenitic Fe-C-Z solutions (where Z represents a substitutional solute) was developed by extending a solution model which was previously applied to austenitic Fe-C alloys. The model assumes that each carbon atom in the solution excludes H interstitial sites from occupancy by other carbon atoms rmd thai otherwise the assembly of carbon atoms is equivalent to a modified Langmuir lattice gas. The results of the treatment provide theoretical justification for a phenomenological expression previously developed to represent the influence of substitutional solutes on the thernlodynamics of carbon in austenitic Fe-C-Z alloys. The expression is: where Kz is a parameter which characterizes the Fe-C-Z system at a given temperature and Xz and xj are the concentrations of substitutional solute and interstitial carbon expressed as atom ratios. The parameter, Kz, was associated with the differ- A number of investigators have measured the influence of various substitutional solutes on the carbon activity in austenitic Fe-C-Z alloys, where Z represents any substitutional solute. Experimental information is available for alloys containing the following substitutional solutes: Mn,' Si,' Ni,2-5 CO,'-', Cr,5, 9-11 CU,4 Al,= v,11, 12 and Ti.13 This information is essential for studying many phenomena in Fe-C-Z alloys, particularly diffusion and diffusion-controlled phase transformations For example the pffprts nf various ence between the interaction energies between carbon atorns and host-lattice atoms in the Fe-C-Z solution and the corresponding energies for the Fe-C solution. The carbon activity in a ternary Fe-C-Z alloy, ac, was obtained in terms of the composition of the alloy and the single parameter, Kz: where y° is the Henry's law constant for the binary Fe-C solution. Both y° and H crm be determined from the data for Fe-C solutions, without recourse to any experimental data for Fe-C-Z solutions. The theoretical treatment was extended to alloys containing several substitutional solutes. By neglecting interactions between the substitutional solutes, an expression for the carbon activity in multicomponent alloys was obtained in terms of the Kz values characterizing ternary Fe-C-Z systems. substitutional solutes on the rate of pearlite growth is explained14 on the basis of their effects on carbon diffusion, which result from their influences on the carbon activity in the solid phases. In addition, recent studies have emphasized the dependence of the pro-eutectoid ferrite transformation15 and other diffusional processes in austenite16 on the influence of substitutional solutes on the carbon activity in austenite. They have indicated the need for suitable analytical expressions to represent such influences. The present authors previously developed general phenomenological expressions to represent the equilibrium partitioning of carbon between Fe-C alloys and Fe-C-Z alloys.'2 The expressions are applicable to all the austenitic Fe-C-Z alloys for which experimental data are available, and are sufficiently simple to recommend their general application. For alloys in

Jan 1, 1969

By Richard P. Gerwels

Minas de Matahambre, a copper mine located 100 miles southwest of Havana, Cuba, has produced 10 million tons of copper ore since it was first opened up in 1913. During the mid-1950's the mine was producing approximately 1000 tpd and had attained a depth of 3600 ft. As shown in Fig. 1, the property contains three shafts: the No. 1 shaft, 2100 ft deep and located 2000 ft south of the No. 2 shaft, provided service to the 2100 level; the vertical 3600-ft No. 2 shaft handled all production to the 3400 level; the No. 3 shaft on the northeasterly fringe of the mining area was in a semi-active status.

Jan 12, 1960

By J. Offeringa, C. van der Poel

The report describes scaled model experiments on the recovery of oil from porous sands by the injection of miscible liquids [solvents] and the subsequent recovery of the solvents by water flooding. Special attention has been paid to the scaling problem. Scaling rules are deduced and their correctness is checked by carrying out experiments in tubes of various sizes. Data are submitted on the effect of the viscosity ratio oil-solvent on the efficiency of the displacement process, the viscosity ratio varying from 1.5 to 5,000. Breakthrough recoveries obtained when flooding with kerosene as a solvent, are equal to those obtained in water flooding at the same viscosity ratio, indicating that he phenomenon of viscous fingering is decisive. After breakthrough, however, flooding with a miscible liquid becomes much more efficient than a water flood and this is more pronounced as the viscosity ratio oil-solvent is higher. Although high oil recoveries are obtained and most of the solvent in the sand can be recovered by a subsequent waterdrive, a straight flood with miscible liquids does not appear economically attractive because of the large quantities of solvent required. Therefore, a circulation process is introduced, the features of which are described in this paper. Though by means of this circulation process the amount of solvent required can be drastically reduced, the process is not yet economic. SCOPE OF THE INVESTIGATION The recovery efficiency by water flood of oils of viscosities exceeding 50 cp is low. As interest in production of these highly viscous oils is growing at the moment, it was considered worthwhile to gain basic information on the feasibility of first flooding such oils with a low viscous miscible liquid [solvent] and subsequently producing the latter in a conventional way, e.g. by water flooding. The method has the obvious drawbacks that return on the investment is delayed until water flooding has begun and that it requires the investment of a more valuable product to produce a less valuable one. On the other hand, it may be expected that the displacement of one liquid by another is more efficient when the two liquids are miscible than when they are immiscible. As laboratory data on this point are scanty, the present investigation seemed justified. Another argument for carrying out these experiments is that they present a valuable contribution to our concepts of the scaling problem in reservoir engineering studies. Some major difficulties which are encountered in the scaling of the waterflooding process such as the scaling of the capillary forces and the difficulty of obtaining the same permeability characteristics in the model do not present themselves in this case. As the fluids are miscible capillary forces do not play a role and as there is only one fluid phase, Darcy's law is valid in its original form. Consequently it is felt that the scaling rules can be deduced with a greater amount of certainty. An essential feature of the experiments is that they are scaled model ones, which are, however, somewhat

Jan 1, 1955

By C. D. King

DURING the 30-year period spanned by these annual Howe Memorial presentations, many lecturers could proudly claim a kinship either as a student or an associate of the man whose memory we honor. Although it has been my good fortune to have attended many of these annual lectures, it was not my privilege to have known Henry Marion Howe personally. However, his great repute as teacher and scientist was known to all undergraduates of my day and the later years have enhanced my appreciation of his wisdom and foresight. Those who knew him well have said he derived particular pleasure from speculations on the future world of metallurgy. For this reason, I feel that perhaps he would not be unsympathetic to a lecture in his honor which departs from the highly instructive scientific presentations made in the past by so many able Howe Memorial lecturers, and which is concerned more with the practical phases of various steelmak-ing processes and some speculations on their future form and relative importance. The word "revolutionary" is frequently applied to each seemingly important improvement in the production of steel ingots, but in retrospect these changes, impressive as they appear at the time, are merely steps of progress. In the hundred years from the inception of tonnage steelmaking, only three processes can be truly classified as revolutionary. They are the pneumatic process, known in this country as the bessemer process; the reverberatory method called the open hearth process; and, the electric furnace process. There have been many variations and combinations of the three fundamental methods, but they remain truly the only revolutionary methods in steelmaking since its early history. Everything else has been evolutionary, in effect. doing the same things that we have done in the past but doing them better, correcting our errors through experience, and slowly but inevitably reaching a higher state of accomplishment. It has often been said that coming events cast their shadows before, and the production of steel ingots is no exception. As a result of the unrelenting demands of World War I1 and the years that followed, truly impressive progress has been made in steel ingot production. The incessant pressure for immediate results during this period required the employment of initiative and daring, as in few past decades, and many developments were brought to fruition. Of equal importance is the possible effect on future steelmaking methods of the many ideas initiated but still in formative stages. Fig. 1 portrays ingot production in the United States by the three fundamental processes over a period of 75 years and is interesting because it poses some questions as to future trends. The early ascendancy of the bessemer, its replacement in importance by the open hearth process, the amazing growth of the latter, and the recent challenge of the electric furnace are evident from the chart. Management is fully aware of these changes, but is even more interested in the future trends. Our concepts of the relative importance of the more recent developments and their possible effect on future processes may perhaps be best exemplified by a specific, hypothetical problem. Let us assume management is contemplating a new ingot producing plant with an output of 100,000 net tons per month, located in an area where some purchased scrap may be obtained but where by far the largest component will be own-produced blast furnace iron. Management requires a process or combination of processes which will yield highly uniform quality characteristics in the ingot form, and represent the soundest selection in investment and operating cost. Under these conditions, the obvious selection for the past four decades has been the open hearth process but, in view of more recent developments, management may believe that it is no longer permissible to disregard other possibilities with impunity. Accordingly, to be assured of the best possible selection, they request that you review not only the possibilities of utilizing the conventional open hearth, duplex, bessemer, and electric furnace methods, but also the more recent developments, such as the turbo-hearth, the Linz-Donawitz method, the Perrin modifications, and other possibilities. With this background, one might then appraise the relative importance of these methods to meet a specific need, and concurrently speculate on the forms that future ingot processes will assume and the relative importance of these processes.

Jan 1, 1955

By R. McNeill, D. E. Weiss, E. A. Swinton

In a continuous countercurrent exchange process, an alteration in any one of the operating conditions has a complex effect on the others, which can only be predicted by employing the transfer unit or the theoretical stage theory on a basis of trial and error. A simple method is described for illustrating diagrammatically the behavior of a counter-current system, the equations being simplified by means of a concept the maximum hypothetical exchange performance. An example based on a typical metallurgical system is given, in which a divalent metal is recovered from a dilute solution, the resin being regenerated continuously by a monovalent ion. Useful conclusions are drawn from a study of the theory. Practical methods for performing continuous ion exchange are discussed, and the development of equipment based on modified ore dressing jigs is described. A swinging sieve jig contactor is evaluated experimentally. DURING the last decade, the new synthetic ion exchange resins have been applied extensively in industries outside the field of water treatment, but there is no record of a continuous counter-current process operating on an industrial scale. Attempts have been made to devise a satisfactory process but many problems remain to be solved. The basic principles of continuous processes will be outlined, as well as the major problems in their operation and the progress made in the CSIRO laboratories toward the development of satisfactory industrial techniques. In the metallurgical field ion exchange resins can be used for various applications such as the recovery and concentration of valuable metals from mine waters,' the regeneration of pickling and plating liquors," the prevention of pollution by waste effluents and the recovery of the constituents from them," and the purification of valuable metals such as the rare earths by chromatographic fractionation on columns of ion exchange resins.7,8 . Turther applications undoubtedly will be found in the field of hydrometallurgy where the use of ion exchange resins would enable direct extraction of the desired metal ion from the filtered leach liquor or the leach pulp. For example, an ion exchange process has been described recently for the extraction of gold from a cyanide leach pulp." A continuous process would have advantages in many applications over the usual process employing a fixed bed and intermittent cycle. In a recovery process, it would yield a product stream of steady purity and concentration, it would waste less water in rinsing, and if the contacting apparatus were efficient less resin would be used, since each portion of the resin would be cycled as soon as it was loaded instead of lying idle until the whole bed was ready for regeneration. A very major advantage is that it would be simpler to control automatically. It is probable that continuous operation will be the key for really large scale applications of ion exchange. The flow sheet of a continuous ion exchange recovery-concentration process is illustrated diagrammatically in Fig. 1. Dilute liquor containing the valuable ion flows through the stripping section countercurrently to a moving bed of resin and leaves after a final contact with freshly regenerated resin. The resin leaves the unit almost in equilibrium with the incoming liquor and then flows to the regenerating unit where it is treated by a slow countercurrent flow of concentrated regenerant solution. The adsorbed ion is displaced from the resin and appears in the concentrated product stream. The resin then must pass through a rinse unit or section where regenerant entrained by the resin is washed back into the regeneration section by water. The regenerated and washed resin is then recycled back to the stripping section. I. Theoretical Operating Behavior of Continuous Ion Exchange Stripping System The simple theory of continuous ion exchange is analogous to that of solvent extraction and other diffusional transfer operations and is governed by the equilibrium relationship, the mass balance, the rates of mass transfer, and the contacting efficiency of the unit. Equilibrium Relationship—The relative affinity of two ions A and B, for a particular resin immersed in their solution, can be expressed by plotting compositions of the solution against compositions which exist in resin in equilibrium with those solutions, i.e. C/Co vs q/a where C, is the total normality of the solution, C is the normality of ion A in the solution, a is the total exchange capacity of the resin in gram equivalents

Jan 1, 1956

By J. B. Cheatham, R. B. Paslay

Rock stresses and steady-state flow rates induced by the pressure gradient associated with the flow of formation fluid into a borehole have been analytically determined for a permeable, elastic material saturated with an incompressible fluid. In this analysis, the material properties and loading are considered to be symmetric about the axis of the borehole and independent of axial position. For Case I the material is assumed to have uniform permeability in the radial direction, whereas for Case 11 the permeability is assumed to have been reduced in a localized region adjacent to the hole by either normal well completion and production operations or deliberate plugging during air drilling. Results of a numerical example indicate that, in the absence of plugging, the rock shear strength must be approximately two-thirds the formation fluid pressure in order to prevent rock failure. The required rock strength is high for small radial zones of plugging and decreases as the region of reduced permeability becomes larger; however, a depth of plugging can be reached beyond which there is no real gain in strength, although the flow rate can be further reduced. INTRODUCTION During normal production of oil from a well, it is often desirable to increase the production rate of the formation fluid by increasing the pressure gradient through the formation adjacent to the borehole. Depending upon the magnitude of this pressure gradient and strength of the rock material, this production-rate increase can cause sloughing of the hole wall. In many cases, the production - rate increase can result in excessive sand production, increased wear of production equipment, lost production time and expensive workover jobs. In addition, the phenomenon of increased rock bit penetration rate with the use of a gaseous instead of a liquid drilling fluid has been observed in oilfield drilling operations and experimentally demonstrated by various investigators for several years. The improvement obtained by employing this technique can be quite significant and offers apromising method for reducing drilling costs. However, air drilling is currently limited to geographical locations where high-capacity water-bearing formations are not encountered. This limitation has prevented widespread adoption of air-drilling techniques, because the water influx into the borehole interferes with efficient removal of the drilling cuttings and usually results in a condition such that the bit becomes "balled-up" or stuck in the hole. In an attempt to remove the water - intrusion limitation from air drilling, various chemical and mechanical water shut-off methods have been proposed. Goodwin and Teplitzl suggested one such proposal whereby the permeability of the water-bearing rock structure was reduced in the vicinity of the borehole. Although the development of a shut-off method based upon this approach would certainly be welcomed by the oil industry, it is conceivable that, under certain conditions of the pressure gradient, strength of the rock material and depth of the modified permeability zone, a stress field can be created that will result in an unstable hole. As part of their study, an analytical solution is given for stresses in an idealized model of a hole and the surrounding rock material. The purpose of the present study is to extend the analysis of Goodwin and Teplitz to gain more insight into the details and consequences of excessive production rates and formation water shut-off. In particular, simplified models of these problems have been analytically examined, which makes possible the evaluation of the type of stress fields that can be anticipated as a result of these production and drilling practices. Both problems solved concern the determination of the steady-state volume flow rate of the formation fluid and the resulting steady-state stress and displacement distribution in a hollow, cylindrical configuration. The cylinder of Case I, corresponding to the production-rate problem, consists of a material with a constant permeability from the inside surface to the outside surface; the cylinder of Case 11, corresponding to the water shut-off problem, consists of a material with a constant permeability from the inside surface to an intermediate concentric cylindrical surface and a second constant permeability from the intermediate surface to the outside surface-