Search Documents

By Robert B. Fulton

Staurolite, an iron aluminum silicate mineral, is used industrially as the source of aluminum in portland cement manufacture in areas where the aluminum constituent is not economically available from shale or argillaceous limestone. It is also used as a high value- in-use sand blasting agent and as a premium grade foundry sand. It is produced by E. I. du Pont de Nemours & CO. as a coproduct in titanium mineral production in Florida where it was first recovered on a commercial scale in June 1952 from the Pleistocene sand deposit known as Trail Ridge. In the Trail Ridge deposit it comprises about 36 of the heavy minerals, the principal other heavy mineral constituents being ilmenite, leucoxene, rutile, zircon, kyanite, sillimanite, and tourmaline. Staurolite and the other silicate nonconductive heavy minerals are separated from the conductive titanium minerals on high-tension separators. The silicates are then separated from one another magnetically, the staurolite being relatively magnetic. In the total processing, 200 tons of raw sand yield 7 tons of heavy mineral concentrate from which about one ton of staurolite is recovered. Staurolite production is approximately 100,000 net tpy. No other commercial production of staurolite is known. This process yields staurolite concentrates of the characteristics given in [Table 1]. These concentrates are sold as three products with the size distribution of subrounded particles shown in Table 2. All three grades are used in sand-blasting for cleaning metal, for paint removal, and for cleaning buildings. Staurolite compares favorably with lower unit cost abrasives, such as boiler slags and mineral aggregates, in applications where the abrasive is used only one time and is not recovered. Because it is hard, fine, clean, and dense it can reduce blasting time, with less material reportedly being required

Jan 1, 1975

Doctor David Yang has presented an important new flotation development in the area of fine particle flotation technology; at the same time Dr. Yang presents an explanation for the effectiveness of this improved new fine flotation system in terms of an optimum dispersion state. The same statement is made for the case of carrier flotation (ultraflotation), in the removal of anatase from kaolinite by addition of calcite (selective flocculation of the anatase - calcite system and dispersion of kaolinite). Dr. Yang's data and statements raise some important questions, and I will adress myself to the more fundamental aspects of this new flotation system. The addition of sodium silicate, well known as a good depressant-dispersant agent for siliceous gangue minerals, is proved to be greatly enhanced by the incorporation of polyvalent metal salts into sodium silicate prior to flotation, producing in this manner a condition, as described by Dr. Yang, of optimum dispersion, which in the case of fine-grained oxidized taconite can be described as selective flocculation (coagulation) of hematite and almost complete dispersion of siliceous gangue components. Dr. Yang recognizes that the main mechanism, while not completely understood at this time, seems to operate by modifying the surface characteristics of the gangue slime particles so as to prevent collector from bonding there to, and making the particles strongly hydrophilic so they will become fully dispersed and consequently will not float during froth flotation. At the same time it appears that the conditioning reagent also modified the surface characteristics of the floated minerals (hematite and spodumene in this case) so that they will aggregate and tend to more readily adsorb the collector, resulting in an improved flotation kinetics and selectivity.

Jan 1, 1979

By Persifor Frazer

It was my intention to have directed the attention of the members of the Institute to a complete series of rocks representing the older and middle formations represented in Pennsylvania, but time has been insufficient for the purpose, and 1 have been unable, in the first attempts to reduce the sections of those rocks, which I have brought with me to this meeting, to the requisite thinness necessary for exhibiting the peculiarities of their constituent minerals. The rocks represented here belong to the various horizons already mentioned, and include gneiss, ferruginous gneiss, chlorite slate, quartzites, and hydro-mica slates, limestones, dolomites, ferruginous conglomerates, quartz conglomerates, " Potomac marble" (nether member of the Mesozoic series), dolerites, and a syenite. The order in which these are named is, roughly, the order .of geographical position in a section line from southeast to northwest, commencing at the intersection of the Northern Central Railroad with the Maryland line, and ending a few miles from the town of York, and a short distance within the marginal outcrop of Mesozoic red sandstone. In such a geographical section all the rocks above mentioned would be encountered in the given order except syenite, about which a few words are to be said in a moment. (But this is far from representing the rocks in their geological sequence.) There is nothing of unusual interest to present to your notice in these slates and quarteites. The limestones were carefully searched tinder 450 diameters microscopic power, but they show no signs of organic remaius. One section of a fine-grained Triassic sandstone contains a very beau- . tifully banded plate of quartz. But the objects of greatest interest at present are the specimens of trap. The more fine-grained and compact traps were collected from

By John J. Theiler

Early in 1963, the Inspiration Consolidated Copper Co., at Inspiration, Ariz., began a program to make automatic the lubrication of several critical points on their KW Dart 37SL haulage trucks. Prior to installation of the automatic lubrication system, all the haulage trucks were serviced by hand every three shifts. Now, with automatic lubrication, the service period has been extended to four shifts. What are the principal benefits to be expected from such a system? 1) Uninterrupted production; 2) extended machinery life; 3) good housekeeping; 4) lower maintenance costs. Of these points, the most important to truck maintenance are extended component life and lower maintenance costs.

Jan 5, 1965

By H. A. Wilmeth

IN 1955, before planning an accelerated stripping program, Chino Mines Div. began an engineering study to improve data for estimating truck haulage costs for any future haulage layout. The study aimed to develop: 1) significant unit costs, 2) a method of estimating travel time from which truck needs and future stripping rate could be determined, and 3) yardsticks of performance to measure haulage efficiencies. It was suggested that to provide significant unit costs, expense accounts should offer management two types of cost control information-unit cost yardsticks with which monthly unit costs could be compared and unit costs for estimating future expenses for any haulage layout.

Jan 5, 1958

By A. R. Troiano, A. B. Greninger

There is need for an adequate working hypothesis that would describe at least qualitatively the crystallographic mechanism for the transformation from austenite to martensite in steel. A general theory would not only be of great assistance in the correlation of existing data and in planning future experimentation, but would also form the basis for an eventual explanation of the property changes that accompany lattice transformations. The mechanism of martensite formation described in the following pages is the outcome of two new experimental determinations: (1) the accurate evaluation of the lattice relationship between austenite and individual crystals of martensite, and (2) the measurement and analysis of the change in position that a volume of austenite undergoes when it transforms into a crystal of martensite. For this latter study, the stereographic analysis of shear was employed; this method greatly simplifies the solution of lattice-shear problems, and some space is devoted to its description. Lattiice Relationships and Habits PREVIOUS WORK The lattice relationships between austenite and martensite in carbon steels have been studied by Kurdjurnow-and Sachs,' and by Wassermann;2 and in iron-nickel alloys by Nishiyama.3 Wassermann,2 and Mehl and Derge.4 The studies by Kurdjumow and Sachs and by Wassermann were made on single (austenite) crystals of quenched 1.4 pct carbon steel, and the results of these two independent studies agree closely with the postulated lattice relationships: (III)r||(0ll)a [101]r [111]a [1] Both Nishiyama and Wassermann worked with an alloy of iron plus 30 pct nickel (all austenite at room temperature), and "martensitic alpha" was formed by cooling in liquid air. They agree that the lattice relationships for these conditions are: (lll)r||(011)a [112]r[011]a [2] Mehl and Derge worked with a range of iron-nickel alloy compositions centered about 30 pct nickel. They concluded that when the transformation takes place near room temperature or above, relationship [l] holds, but if the same specimen is made to transform at -195°C, relationship [2] obtains;intermediate temperatures evidently produced a combination of these two relationships. Sachs and co-worker~,1,7 as well as Nishiyama,3 have proposed transformation mechanisms for martensite formation.* Both of the mechanisms picture the transformation as initiated by shearing movements along the octahedral [Ill] plane of austenite, followed by suitable expansion and contraction to complete the transformation. These mechanisms have been described and commented upon by Mehl, Barrett, and Smith,8 Mehl and Derge,4 Wassermann,2 and others, and generally accepted by investigators in this field. Greninger and Troiano9 have recently published the results of a detailed study of the shapes and orientation habits of martensite crystals in plain-carbon and nickel steels. They found that, contrary to previous assumptions, martensite plates form not along the octahedral planes but along austenite planes of very high indices; these results were in line with those of previous studies of martensite reactions in nonferrous alloy systems by Greninger and coworkers.6,10 Greninger and Troiano concluded that the transformation theories of Kurdjumow and Sachsl and of Nishiyama3 are untenable. Phragmén11 reached a similar conclusion. EXPERlMENTAL METHODS The object of this particular study was the evaluation of (1) lattice relationship between austenite and martensite, and (2) relationship between the martensite lattice and the martensite plate. The technique used for solving these problems was similar to that used by Greninger6 on martensitic structures in 8 copper-aluminum alloys. Briefly, the method consists of grinding and polishing a specimen on a surface parallel to an individual martensite plate and thus exposing a single martensite crystal for an area of l to 3 mm. The orientation of this exposed martensite crystal is then determined by means of a back-reflection Laue X ray pattern.12 Another pattern is obtained from the matrix crystal, and a stereo-graphic plot of data from these two patterns then provides the solution to the problem. It is necessary to repeat this process on several crystals in order to determine whether or not the solution is unique.

Jan 1, 1950

William Clinton Brown, Brooklyn, N. Y.: The demand for an apparatus for cooling water for condensers, refrigeratingmachinery and air-compressors, as well as water-jacketed furnaces, has led manufacturers to put such an apparatus on the market, so that it is now possible to purchase a cooling-tower, properly designed and constructed, by simply stating the amount of water to be cooled and the temperatures of the hot and the cold water. The principle is similar to that described by Mr. Henrich, but wood is not used in the best apparatus. There are two great objections to wood: First, it cannot last long under the very trying conditions to which it is subjected; and second, it absorbs the organic matter with which water in constant use becomes impregnated, and the resulting odor is very disagreeable. A few days ago I saw a cooling-tower and condenser, built by the Henry R. Worthington Co., in operation at the Edison electric-lighting station in Brooklyn, N. Y., cooling the water for a 700 horse-power condenser. It consisted of a large stack of iron, about 15 feet in diameter by about 30 feet high. This stack was filled with tiling through which the water falls. A whirligig distributes the water evenly over the top, and a large fan, about 6 feet in diameter, driven by a 10 horse-power electric motor, blows air into the bottom, thus giving a positive circulation. The water, in running down the sides of the tiling, is met by the blast of air, and enough is evaporated to cool the rest. The vacuum-gauge on the condenser showed 26 inches; so the condenser was undoubtedly getting sufficient cool water.

Jan 1, 1896

By C. G. Dunn, F. Lionetti

The energy associated with grain boundaries in polycrystalline aggregates is believed to play a major role in grain growth processes and, when growth ceases, to determine the final equilibrium grain boundary angles. Further, the energy of grain boundaries of recrystallization nuclei is a factor in nucleation processes. It is important to know, therefore, how the energy per unit area of a grain boundary, that is, the grain boundary surface tension y, depends on the difference in orientation of the two lattices of the grains producing the boundary. Although the problem is important, surprisingly little has been done toward a quantitative evaluation of the effect of orientation difference on grain boundary energies. C. S. Smith1 recently has discussed this problem and in addition to showing effects of orientation difference on equilibrium angles has shown a variety of interesting effects of surface tension on the appearance of microstructures. Fig 1 and the following relations expressed in Eq 1, which connect equilibrium grain boundary angles and surface tensions, illustrate equilibrium conditions which are believed to hold true in metals. ?l2 _ ?23 _ ?l3 [1] sin ?3 sin ?1 sin ?2 Clearly any two of these surface tensions can be expressed in terms of the third when the equilibrium angles ?1, ?2, and ?3 are known. Applied to the present problem for solid state equilibrium of three grains, the angles ?1,?2 and ?3 must be measured in a plane perpendicular to the line of junction of the three grains. Normally a direct determination of these angles from random microsections is impossible. Consequently Harker and Parker2 and Smith1 (except for some measurements on flat specimens) resorted to a statistical method to determine equilibrium grain boundary angles. Smith reported that grain boundaries meet the surface of a piece of metal nearly perpendicularly. He reported also, in connection with direct angle measurements on flat specimens with grains extending through the thickness, that angles varied appreciably from 120" and concluded that there was a measurable effect of orientation difference on surface tension. Another direct way of determining equilibrium angles and a method adaptable to studying particular configurations, recently suggested by Dunn,³ is to use a three-grain flat specimen with orientations of grains so chosen that the junction line of the three grains will be straight throughout the thickness and perpendicular to the surface of the specimen. Choice of orientations is possible when individual grains of each group can be grown to predetermined orientations through the reorienting and growth of " seed crystals " as described.³ Not only is it possible, for example, to have grains with the same crystallographic plane in the plane of the specimen, but a given orientation difference between two grains can be made a common factor to an unlimited number of three-grain groups while a series of orientation differences is investigated. Any effect of anisotropy of gas-solid surface tension due to grain orientation should be minimized by having all gains oriented the same with regard to crystallographic plane in the plane of the specimen. Another feature of the three-grain group is the notched grain boundaries as shown in Fig 2 for one specimen (S4). The notches serve to anchor the end positions of the grain boundaries (especially at high temperatures) while the central and junction point of the grains moves toward an equilibrium position. Final equilibrium should produce straight grain boundaries if the notches are very narrow and if changes in orientation* of the grain boundary do not alter the surface tension.† If one assumes the straight line condition and no change of surface tension with small changes in grain boundary orientation and finds the equilibrium configuration by a minimization of the grain boundary energy, one obtains the relations given in Eq 1. The approach to straight line boundaries or to minimum energy configurations in specimens containing large grains, such as those used in the present investigation, may be very slow compared with the approach to equilibrium conditions for the grain boundary angles. It may be desirable, as proved to be the case in the present investiga-

Jan 1, 1950

By C. K. Leith

THE questions as to what grades of ore it pays to conserve for the future, and the valuation of low-grade reserves, are becoming immediate and definite as applied to individual ore deposits, and seem to call for some sort of quantitative answer. Both opinion and practice involving these questions differ widely. The number of variables in this problem is so large that final solution will perhaps never be agreed upon, yet there seem to me to be certain controlling factors which can be placed in quantitative relation and serve to reduce the number of variables which it is necessary to consider in a given instance. I assume that it will not pay either for the individual or for the State to conserve any ore when the present cost of conservation (by stock piling or otherwise), when compounded at 6 per cent. interest for the number of years which would elapse before this ore is used, will exceed the profit which the ore will yield when it is used. It may be urged that any loss to the individual may be made up in gain to the State. This might be true if there was any definite limit to the amount of iron ore, but when we remember that iron makes up .4 per cent. of all the rocks of the earth and the amount of rock carrying iron in excess of 20 per cent. is for practical purposes, unlimited, it is apparent that posterity is assured of its iron ore. The changes will be mainly in methods and cost of extracting the ore. Therefore, any expenditure of money or effort now, which when compounded will exceed the worth of the effort or money needed in the future to utilize the iron, is a net loss both to the individual and to the community.

Jan 2, 1914

By P. A. Toynbee, D. G. Wilson

The combustion performance of sub-bituminous slack coal is greatly improved by the removal of the smaller size fractions. Screening processes are not well suited to the size separation, at 1/8 in. or 1/16 in., with coals which are normally wet, and the use of an alternative size-separation device has been investigated. It is felt that this classifier might be applied equally well to other minerals in cases such as this, where precise size limits are not essential. Coal is dropped as a curtain onto a curved metal plate, shaped rather like a ski-jump. The smaller particles, slowed up in their free fall to the plate and also by contact with the metal, leave the plate with a lower horizontal velocity; they can be separated from the larger particles by virtue of their shorter trajectory. The principle of the classifier is obvious from the diagram (see Fig. 1) which shows also the positions, relative to the curved plate, of the point of coal feed and of the dividing plate which separates the streams of coal particles. The horizontal distance between the curved plate and the dividing plate is varied in the tests. It is designated in the general case, by X. Tests were carried out using slack coal with a free moisture content higher than that expected in any commercial operation. The results given in Table I. show the percentage recovery of upgraded product, and the cumulative screen analysis of both the upgraded and reject material, for three different positions of the dividing plate. The results show, for example, that the original coal can be upgraded, with a recovery of 80%, to reduce the minus 1/8 in. frac-

Jan 1, 1965

By W. J. Sharwood

Discussion of the paper of W. J. SHARWOOD, presented at the San Francisco meeting, September, 1915, and printed in Bulletin No. 104, August, 1915, pp. 1671 to 1675. FREDERIC P. DEWEY, Washington, D. C. (communication to the Secretary*).-Even if the data given should be considered sufficient to support properly the empirical rule as stated, this rule would be of extremely limited application in miscellaneous assaying. Tile fixed conditions must include equality of gold and silver where mixed beads are concerned, owing to the wide variation in the specific gravity of gold and silver. Also, the fixed conditions must include the presence of the sane amounts of other base metals besides lead. Such an agreement is .often lacking even in the beads from two fusions of the salve ore. In practical work it is sufficiently general to be called universal that cupellation beads are not pure precious metal. An apparent loss in cupellation is an algebraic sum and in many cupellations the gains exceed the losses, especially with large beads where tile gains lie so completely in the judgment of the cupeller. For several years I have been engaged in an investigation into the conditions affecting the accuracy of gold-bullion assaying, and have just completed an examination of cupels which included the assaying of 10,000 used cupels. The grand result of the cupel work is an emphatic warning against drawing rigid conclusions regarding cupellation. It is so easy to say "If all other conditions remain the Same," but it is extremely difficult, and in practical work impossible, to maintain equal conditions. Cupel absorptions, which constitute such a large proportion of cupellation losses, and in many cases the only loss, may vary considerably in different parts of the same row of cupels, even in carefully regulated work.

Jan 12, 1915

By R. S. Rickard

Chemical processing of ores has gained new im¬petus in recent years. The reasons are many. They range from the need to process ores that are difficult to beneficiate to the avoidance of pollution. Although many think of chemical processing as a hydrometallurgical operation there are other techniques. An example is chlorination. Chlorination, although examined and discarded by many investigators, is again being considered as a means of extracting uranium1, treatment of silver-lead ores2, and the recovery of base metals from pyrite cinder and ores3. Segregation roasting of copper and nickel ores, a process similar to chlorination, is another chemical treatment being revived.

Jan 1, 1970

ELECTROREFINING Canadian 1,023,691 -Removal of bismuth from slime filtrate in the Betts process refining of lead. The filtrate is subjected to electrolysis in a cell having an anode of crude lead and a cathode of refined lead under operating conditions to preferentially deposit bismuth on the cathode. The substantially bismuth-free filtrate is recycled for use in the process as the electrolyte for producing high-purity lead. S. Hirakawa and R. Oniwa, assigned to Mitsui Mining & Smelting Co., Ltd. Jan. 3, 1978. 8 pp. (204-73). Filed: 2-18-74 (192,810). Same: U.S. 4,026,776, dated May 31, 1977.

Jan 1, 1979

By Samuel Daniels

THE Al-Cu-Ni-Mg alloy is much benefited by heat treatment and, in such con¬dition, is preferable to the Al-Cu-Fe-Mg alloy either as cast or as heat-treated, when both are reheated to temperatures of from 400° to 600° F. and compared, cold, with respect to strength and to hardness. The main differences between the alloys do not arise until the reheating temperature exceeds 400° F., above which they gradually soften. This softening is characterized metallographically by the appearance of intragranular precipitate. The Al-Cu-Ni-Mg alloy is weakest and least hard after being reheated at 600° F., the AI-Cu-Fe-Mg alloy at about 700° F. The former starts to reharden at 700° F., the latter at 800° F. There is a tendency for both alloys to lose strength and hardness with prolongation of time at the reheating temperatures of 500° and of 700° F. The Al-Cu-Ni-Mg alloy is considerably stronger and harder than the Al-Cu-Fe-Mg alloy when both are heat-treated and reheated for long periods of time at 500° and 700° F. Although the latter can be made harder initially than the AI-Cu-Ni-Mg alloy by suitable quenching and aging, heat treatment, in general, favors the retention of this initial (strength and) hardness after reheating to a much greater degree in the Al-Cu-Ni-Mg alloy. The percentage of elongation of the two materials in any condition is very small. CERTAIN aluminum alloys have been used for pistons and other parts operating at temperatures up to 650° F. because of their lightness, high thermal conductivity and specific heat, fair strength and hardness at elevated temperatures, excellent machineability, and moderate resistance o corrosion. In the piston, the inertia forces and the bearing loading and with this the vibration are decreased. The piston head functions at a lower temperature (about 200° F. below one of cast iron), so that, because of the lessened tendency toward carbonization and detonation, higher compression ratios may be used. On the other hand, the aluminum alloys do not have the wearing and bearing qualities of cast iron; also they have a large coefficient of expansion, allowance for which must be made in the design.

Jan 2, 1926

By H. P. Rassbach, E. R. Saunders

MUCH progress has been made in recent years in the theory and practice of making stainless steel. By effective utilization of oxygen for decar-burization and more suitable alloying agents, it has been possible to attain consistent production of very low-carbon stainless steel. In order to facilitate economical production of stainless steels, the Electro Metallurgical Co. has carried out an extended experimental program that has clarified some of the complex interrelations of temperature and composition under decarburizing and reducing conditions. These results'-:' have been founded in large part on small experimental heats, and in order to confirm their validity and significance under commercial conditions, a survey of stainless steel melting practice has been made with the cooperation of stainless steel producers. Conditions required for decarburization and associated oxidation of chromium, manganese, and iron have been fairly well established in relation to the beneficial effect of the highest practicable temperature. The recovery of chromium and manganese from highly oxidized slags by reduction with silicon has been indicated with somewhat less precision and this study has shown significant deviation in large commercial heats from the small experimental heats. In spite of an unsatisfactory degree of accuracy in estimating the conditions affecting reduction of metallic values, it has been possible to calculate a slag weight in reasonably good agreement with the results observed in large heats. While there still is much to be learned about both the qualitative and quantitative aspects of stainless steel melting, this survey has indicated the manner by which the efficiency of the production process may be measured. Oxidation Period In order to establish practices for the recovery of chromium and manganese from the slag the amounts of these metals oxidized should be known. Moreover, since reduction of oxidized chromium and manganese must necessarily be accompanied by similar reduction of iron, knowledge of the total quantity of metallics oxidized is essential. The relations between carbon, chromium, and temperature under oxidizing conditions were developed by Hilty in 1948.' While it had been realized previously that retention of chromium in the metal during carbon oxidation is favored by high temperatures, the Hilty relation provided quantitative information useful for evaluating melting procedures. For example, it was shown that decarburization to moderate carbon levels can be achieved while retaining substantial amounts of chromium. However, in decarburizing to the low-carbon level necessary for producing 0.03 pct maximum carbon stainless steel, very little chromium remains in the bath at the temperatures generally employed. For this reason, Hilty, Healy, and Crafts' later projected an extension of the chromium-carbon relation to the low-chromium region. Although this chromium-carbon-temperature relation defined the composition of a chromium steel bath at the end of the oxidizing period, it did not provide a direct means for estimating the total amount of metallic oxidation occurring during decarburization of a stainless steel heat. This subject was investigated by Crafts and Rassbach³ and, later, by Hilty, Healy, and Crafts" who demonstrated that metallic oxidation is a function of the chromium content of the initial furnace charge, the minimum carbon content attained, and the temperature. It was further demonstrated from data on 1-ton heats that an empirical relationship exists between the ratio of chromium plus manganese to iron in the slag (S) to the corresponding ratio of these components present in the metal bath. The following expression was derived to permit the calculation of the amount of metallics oxidized during decarburization of a given charge: W-2000 (Cr1 + Mn1)-(Cr2 + Mn2) 1 100s/s+1-(Cr3 + Mn2) where W is the pounds of chromium, manganese, and iron oxidized per ton of charge; Cr1, the percentage of chromium in the charge; Mn1, the percentage of manganese in the charge; Cr2, the percentage of chromium in the bath after oxidation; Mn2, the percentage of manganese in the bath after % Cr + % Mn oxidation; and S =%cr+ % Mn/%Fe in the slag after %Fe oxidation. In order to establish whether the slag ratios of commercial heats are consistent with those found in the experimental heats, the slag and metal analyses shown in Table I were evaluated. These data represent samples taken after the oxidation of two 1-ton and seven 15 to 25-ton heats of types 303, 304, and 304L stainless steel made in chromite, acid, and basic hearths. Fig. 1 illustrates that the results for the commercial heats correlate reasonably well with the relationship originally established for experimental 1-ton heats. It will be noted that in the range of metal composition of these heats, the slag values generally lie above the line. As was suggested by

Jan 1, 1954

Edward Keller, Baltimore, Md. (communication to the Secretary*) :—The authors of this paper are to be commended for their industry and congratulated upon the many interesting results which were the fruit of their researches. While thoroughness has marked their work in general, yet on a few points in particular they have touched but lightly, for which reason, it would appear to me, they have hit wide of the mark in their respective conclusions. The work alluded to pertains chiefly to the occurrence of magnetic iron oxide (ferroseferric oxide) in copper-mattes. Because the authors find that the magnetic residue, left by the dissolved sulphides, varies largely in quantity according to the strength of nitric acid used (with potassium chlorate) in dissolving the mattes, they conclude :— "It appears, therefore, that the ferroso-ferric oxide is the result of precipitation by the oxidizing agent, rather than an original constituent of the matte." In this part of their investigation, Messrs. Gibb and Philp have ignored some well-established data,. In the first place, they have overlooked the fact that there are mattes which are strongly magnetic and others which scarcely show any magnetic property. There is nothing in their work tending to explain this variation. They Seem to have tested none of their products for magnetism. Secondly, they have overlooked the fact that magnetic iron oxide probably exists in all ore-charges in the copper-matting furnaces, and, under the given conditions, that this oxide is very difficult to reduce and to combine with silica to form slag. Thirdly, they pay no attention to the varying specific gravity of the several grades of copper-matte, which may exceed, equal, or fall below that of the magnetic oxide. These are .essential points which, I believe, clearly in-

Jan 1, 1906

By W. W. Norton

The gradually increasing proportion of sulphide ores which lead smelters of to-day are called upon to handle has caused the roasting problem to become one of ever greater importance. Mines have increased in depth, methods of concentration have improved, competition in the purchase of ores has become more keen and it has been clear that new and modern methods of eliminating sulphur must receive a large share of attention. We may look back a score of years or so and recall the old hand roasters, some of which turned out a finely divided roasted product, and others fashioned with a "fuse-box" wherein the roasted ore was slagged. Then came mechanical furnaces of several types, the Bruckner cylinder, the Brown-O'Harra, the Ropp, and others, all designed to cut out the cumbersome hand labor of the old reverberatories. Roasting costs were thereupon reduced and tonnages stimulated to a gratifying extent. However, it seems to have been early recognized that this very feature of a greater amount of roasted sulphide ore as compared with oxide ore brought with it a train of difficulties at the blast furnaces. The mechanically roasted ore was fine physically, the blast furnaces were choked and the troubles of the smelterman were not at an end. Then the Huntington-Heberlein pot system of roasting appeared upon the scene, and later on the Dwight-Lloyd machines were invented, and inasmuch as both of these processes were designed not only to roast the ore but to agglomerate it as well, it was apparent that distinct steps in advance had been achieved. At the Murray plant, modern up-to-date roasting practice is fully exemplified and there are now in successful operation roasting furnaces or devices of several sorts: namely, Godfrey revolving-hearth furnaces, Wedge multiple-hearth mechanical roasters, Dwight-Lloyd sintering machines, and Huntington-Heberlein pots. Godfrey and Wedge furnaces will properly handle material high in sulphur, say ores with 25, 30, and 35 per cent. of that element; D. & L. machines and H. & H. pots will positively not treat efficiently ores or mixtures containing anywhere near the sulphur content mentioned, but are confined to charges containing in the neighborhood of 15 or 18 per cent. In passing, it may also be explained that, so far as the knowledge of the writer goes, Godfrey and Wedge furnaces do not economically eliminate sulphur to an extent

Jan 1, 1915

By Jerome Alexander

It is an outstanding fact of Nature that many of the practical properties of substances are dependent, not on their ultimate chemical composition, but on the kind and degree of aggregation of their constituent particles. Thus, a granite boulder is unmoved by wind or water, but if reduced to a fine dust it will be blown about by the wind and washed away by the rain. Carbon in one crystalline state of aggregation (diamond) is the hardest known substance, whereas in another crystalline state (graphite) it is so soft that it is used as a lubricant. Laying too much stress on the mere chemical analysis of substances is apt to obscure the fact that the nature of the aggregation of their particles is always a factor of importance, and sometimes the most important factor. Colloid chemistry deals with matter in a very fine state of subdivision; its sphere begins with particles just a little smaller than a wave length of light and extends down until they blend into molecular dimensions. With particles of this size, such phenomena as surface tension and adsorption, which depend on the development of free surface, become enormously magnified. Thus a cube of 1 cm. edge has a surface of only 6 sq. cm.; but if it is reduced to colloidal dimensions by being cut up into cubes each having an edge of 0.01 µ (0.00003 mm.), it will yield one million, million, million (1,000,000,000,000,000,O~) such cubes, having a combined area of 600 sq. m., or 21,274 sq. ft. The tiny force with which a drop of rain clings to the window pane becomes a factor to be reckoned with, if the surface involved is increased millions of times. From the colloid-chemical viewpoint, metals and alloys may be regarded as jellies or sponge-like structures,. the viscosity or stiffness of which at ordinary temperatures is exceedingly great; and like all jellies their properties are dependent on the composition and degree of dispersion of their constituent phases. These, in turn, depend on chemical composition, mutual solubility, speed of chilling, subsequent mechanical and heat treatment, etc. In fact, in preparing metals and alloys for practical use, we remove undesirable constituents (as in the conversion of pig iron into steel), add desirable constituents (as in

Jan 1, 1919

By A. W. McReynolds

E. OROWAN*—I observed the phenomenon of jerky yielding many years ago with zinc25 and cadmium single crystals. A significant point was that the jerks occurred not only when the stress was raised but also (sometimes, after a pause of many minutes during which no trace of creep was observable) at constant stress. The phenomenon may be closely linked with the inertia of the testing machine and of the specimen, although the inertia alone cannot account for it. If, during the test, the resistance of the material to plastic deformation suddenly diminishes while the applied force remains constant, a sudden deformation follows until the yield stress has risen, by strain hardening, to the level of the applied stress (= the value of the previous "upper yield point."). When this is reached, the rate of deformation has attained a maximum value because, up to this moment, the applied force was higher than the plastic resistance of the specimen, and the difference was used for accelerating the moving parts of machine and specimen. The kinetic energy accumulated is now transformed into plastic work by further deformation; that is. the deformation overshoots the point at which the plastic resistance equals the applied static force. When the kinetic energy has been used up, therefore, we are left with a specimen the yield stress of which is higher than the applied stress, and no further deformation can occur (apart from a little creep) until either the applied stress has been raised to the new yield stress level, or the yield stress has fallen by thermal recovery to the level of the applied stress. While this occurs, a new upper yield point can develop, for example, by precipitation.26

Jan 1, 1950

By Albert Williams

A large proportion of the work performed in wet-crushing silver mills is devoted to the handling and re-handling of pulp between the battery and the pans. There seems to be no generally applicable substitute for the settling-tanks, and in the present system of constructing mills the tanks involve an amount of labor which may be regarded as disproportionate and unnecessary, in view of the automatic improvements which have been introduced in other directions. This diffculty has been met, however, by Boss's continuous process, in which the pulp flows directly from the mortars to the first of a series of constantly working overflow-pans. This method has been adopted at the Noonday mill, Bodie, California; the Harshaw, Arizona; the Sierra Grande, New Mexico ; and the Prietas, Sonora. The continuous process, while giving excellent results with special ores, and under peculiar local conditions (such as a deficiency in water supply), is not, I believe, claimed to be available for all raw-amalgamating mills, notwithstanding its well-merited popularity for certain work. Some trouble has been experienced from the tendency to concentration in the pans, though this can be avoided by skilful manipulation. It has also the disadvantage inherent in combinations of distinct operations ; it requires a very nice adjustment of the water supply to obtain full battery efficiency without running the pans too thin, though the latter defect is partially compensated for by the gradual thickening of the pulp as it proceeds through the series of pans. The objection is similar to that which holds in a parallel duplex process, that of combining roasting and smelting in a single furnace, where each operation is injuriously affected by the necessity of fitting it in with another and entirely different one.

Jan 1, 1883