Search Documents

By D. S. Rowley, F. C. Appl

Assuming that rock behavior, during cutting with a single diamond, may be approximated by that of a rigid, Coulomb, plastic material, a theory of single diamond cutting action has been developed. Using this theory, the stresses on the diamond cutting surface and the components of the cutting force have been determined. Theoretical results agree reasonably well with available experimental data. The theory of cutting of single diamonds may be used as the basis for subsequent study of the perfonnance of surface set diamond drill bits and other surface set diamond cutting tools. INTRODUCTION For more than twenty years, surface set diamond bits have been used successfully in the mining and petroleum industries to drill and core rock formations that range from medium hard to the hardest known formations. Most extremely hard rock formations cannot be economically drilled or cored by any other means. In view of the growing use and importance of surface set diamond drill bits, it is reasonable to study the way in which these tools cut, and the factors that influence wear of the diamonds. Such knowledge will contribute to better bit design and will improve operating procedures. To analyze the cutting performance of these tools it is appropriate to consider the way in which an individual diamond cuts. Once this is established, the over-all performance of the bits can be determined by considering the total effect of the individual diamonds. In recent years there has been a growing interest in rock mechanics and there now exist several publications dealing with the deformation and failure of rocks. Notable experimental work has been reported by Bredthauer,1 Handin and Hager,2, 3 and Gnirk and Cheatham.4 An extensive collection of data pertaining to rock properties at low confining pressures has been given by Wuerker.5 Cheatham and Gnirk have recently presented an excellent review of the state of knowledge regarding analytical and experimental rock deformation and failure.6 Generally rocks are extremely weak in uniaxial tension, and weak or only moderately strong in uniaxial compression. Both tensile failure and compressive failure are generally brittle in nature. This means that there is little or no deformation or "flow" of the material before shear or tensile fracture occurs. Thus, until fracture occurs, rock behaves very nearly like an elastic material in uniaxial stress. Significant changes in behavior of rock occur under conditions of triaxial compressive stress. There is generally a marked increase in compressive strength and in ductility. It has been demonstrated that the failure becomes plastic (in a macroscopic sense) at sufficiently high values of confining pressure. Sharp wedge chisel indentation studies conducted by Gnirk and Cheatham indicate that many rocks behave in a plastic manner at relatively low triaxial compressive stress states.4 If "failure" under triaxial compressive conditions is considered to be either complete rupture or macroscopic plastic flow, then the general failure characteristics of a rock can be reasonably well represented by the commonly known Mohr envelope. This certainly is not a perfect failure criterion (since the effect of the intermediate principal stress is neglected) but it has been found to be adequate for most engineering purposes. Mohr envelopes usually are constructed graphically using experimental triaxial test data. For purposes of analysis it is convenient to represent the envelope in equation form. Among the several approximate forms appearing in the literature, a parabolic form is suggested by Cheatham,7 and an exponential form is suggested by Paone and Tandanand.8 The exponential form has been adopted for this study, and based on published data, appropriate parameters have been established for 19 rock types. A typical plot of the data compared with the approximate envelope, and a summary of the rock properties and

Jan 1, 1969

By R. J. Brison, O. F. Tangel

The development of a new method of mineral separation was sponsored by the International Salt Company, which requested Battelle Institute to investigate means for improving the quality and appearance of rock salt from the Company's Detroit mine. Although developed specifically for removing impurities from rock salt, the general method may be applicable to other separation problems. The principal impurities in rock salt from the Detroit mine are dolomite and anhydrite which represent 2 to 5 pct of the weight of the mined salt. In the size range from 114 to 112 in. (the range of primary interest in this project) the impurities are only partially liberated from the halite in normal production. Further size reduction to improve the liberation of impurities is not practicable in view of the market requirements for the coarse grades of rock salt. Laboratory separations in heavy liquids showed that, to improve the quality and appearance of the rock salt substantially, it would be necessary to remove not only free gangue particles but also a large proportion of the locked-in particles.

Jan 8, 1960

By J. E. Berry

AII evaluation is made of the acoustic velocity log for measurement of formation porosity. Plots of field-observer1 velocities vs core-measured porosities of sandstones and limestotnes with inter intergranular porosity show that the velocity log gives a useful measure of porotity, in agreement with published data. A new method of plotting electrical and velocity log data makes it easier to recognize hydrocarbon-water coritnct~ from log darn and to make serni-quantitative estinlates of hydrocarbon saturation. Two examples of this interpretation technique are given. This paper also discusses the various factors that affect acoustic velocity and shows how corrections can be made for some of these factors. INTRODUCTION Although the continuous velocity log was developed primarily as an aid to seismic interpretation, it is finding widespread use for measurement of porosity. The purpose of this paper is to evaluate this use of the log. Results are presented for the velocity-porosity relationship in many sandstones and one limestone. Practical applications of porosity values derived from the velocity log to improve interpretation of electrical surveys are presented. Various parameters which affect velocity in porous media are considered. Porosity, composition, cementa-tion, pressure difference (overburden pressure minus fluid pressure), fluid saturation, and wellability are discussed. Some of the ideas are opinions based on general considerations of well logging problems while others are supported by published data and our own observations. Major conclusions from these studies arc given in the body of the paper and detailed discussions of some of the various factors affecting porosity are given in the Appendix. POROSITY Sandstones The primary factor affecting the velocity of sound in porous media is porosity. Wyllie, et al,1 have reported a time average equation for the relationship between velocity and porosity.* This has found considerable acceptance in the industry. Other relationships between velocity and porosity have been proposed, none of which are entirely satisfactory. It is doubtful that any one relationship will completely describe all situations. We have tried an empirical relationship based on correlating log velocities with core-measured porosities. Measured porosities were averaged over a depth interval equal to the spacing used in recording the velocity logs. The depth range for the information used was from 2,000 to 12,000 ft. Velocity measurements were normalized for the effects of depth and overburden pressure. A detailed discussion of the basis for this normalization is given in the Appendix. The change is usually insignificant and when working with individual formations it can be neglected. All velocity measurements were normalized to a depth of 10,000 ft. The velocity-porosity data for sandstones in Fig. 1 came from 20 wells scattered throughout the Mid-Continent and Gulf Coast areas. The scatter of the data points is attributed to three causes: 1. There is no theoretical basis for expecting an exact velocity vs porosity relationship and it is not possible to correct precisely for the effects of such factors as impurities, grain shape, manner of cementation, etc. Some of these factors are discussed in the Appendix. 2. Porosities measured by core analysis are not necessarily representative of what the velocity log "sees". 3. Inaccuracies appear in the velocity log reading. This is particularly true of velocities from one-receiver logging tools.*" A linear-time curve (time-average equation) is plotted in Fig. 1 along with the best straight line through the points. Velocities used for the linear-time curves were 19,500 ft/sec for the matrix velocity (zero porosity) and 5,500 ft/sec for fluid velocity. For clean sandstones with velocities greater than 10,000 ft/sec, there is little difference between the velocity-porosity and the time-porosity curves. Both curves are well within the scatter of data points. The data points in Fig. 1 were restricted primarily to clean sandstones, using the SP and/or gamma-ray logs as clues to the lithology. Where a lithologic de-

By John K. Hammes, Stanley D. Michaelson

Generally, the mining costs reported for the large open-pit operations in the United States and South America lie within the range of $0.20 to $0.30 per ton of material moved. (These operations have strip- ping ratios ranging from 1.5 to 4.0.) Productivities for the larger North American properties are in excess of 200 tons of material per man shift, while those for the South American operations are less than 200 tons per man shift. The most significant variations in cost are in the categories of haulage and general mine cost. Haulage costs vary, as expected, according to the mine elevation, pit profile, crusher location, and accessibility of a dump area, and general cost variations depend largely on the overhead cost items included in this category. Drilling and Blasting Practice The majority of open-pit copper mine production drilling is performed by rotary drills. Hole diameter varies from 6 in. to 12 in., with 9-in. holes being most common, and penetration rates vary from 35 ft to 60 ft per hour.

Jan 1, 1968

By M. R. Tek, F. F. Craig, J. O. Wilkes, C. S. Goddin

The waterflood performance of a water-wet, stratified system with crossflow is computed by a finite difference procedure. The effects of five dimensionless parameters on tile oil displacement efficiency, water saturation con-tour.7 and crossflow rates are evaluated in the absence of gravity forces. Crossflow due to viscous and capillary forces is shown to exert a significant effect on oil recovery in a field-scale model of a two-layered. water-wet sandstone reservoir. The crossflow is at a maximum in the vicinity of the front advancing in the more permeable layer. Under favorable mobility ratio conditions, the comparted oil recovery with crossflow always is interrnerliate between that predicted for a uniform reservoir and that for a layered reservoir with no crossflow. INTRODUCTION The important erects of reservoir heterogeneity on waterflood performance are commanding increased attention in the technical literature. Much of this attention is centered on two categories of layered reservoirs: those in which layers are non-communicating and those in which crossflow of fluids occurs between the layers. In the first category, the reservoir is assumed to consist of discrete layers, each uniform within itself and differing from the others only in such properties as thickness, porosity and absolute permeability. The performance within each layer is calculated by one-dimensional flow theory, and the performance of the total reservoir is obtained by summing individual layer performances. Capillary and gravity effects usually are not considered. Representative publications dealing with thi5 type of reservoir are those of Stiles,' Dykstra and Parsons,' Hiatt,3 Warren and Cosgrove' and Higgins and Leighton." Prediction of performance for reservoirs in the second category is considerably more difficult since viscous, capillary and gravitational forces all play important roles in causing crossflow between layers. A number of authors have investigated the simpler problem of two-dimensional displacement flow in a stratified system with a mobility ratio of unity and negligible capillary and gravity effects.'; Others have considered two-dimensional, non-steady-state flow of a single, slightly compressible fluid in a stratified reservoir. A limited number of laboratory oil displacement tests in layered models with crossflow have been reported. Miscible floods (with resultant zero capillary forces) in layered five-spot models were conducted by Dyes and Braun," who studied the effect of mobility ratio with zero gravity forces, and by Craig et al. 12 who studied the effect of gravity forces at constant mobility ratio. Waterfloods in layered five-spot models (with cross-tlow due to capillary, viscous and gravity forces) were conducted by Gaucher and Lindley,"' who showed the effect of gravity forces in causing underrunning of the injected water and by Carpenter, Bail and Bobek, 14 who demonstrated the reliability of Rapoport's" dimension-less parameters for scaling layered systems. Waterfloods in rectangular layered models were conducted by Richardson and Perkins."' who investigated the effect of velocity at constant mobility ratio and with zero gravity forces, and by Hutchinson," who studied the effects of varying mobility, layer permeability and layer thickness ratios. The differential equations which rigorously describe waterflooding in a heterogenous porous medium are non-linear and do not facilitate analytical solution. By using finite difference approximations it is possible to obtain a solution to any desired degree of accuracy. Such a solution, using an alternating direction implicit procedure (ADJP), is described by Douglas, Peaceman and Rachford.18 In the present study, a computer program using ADJP explores systematically the effects of important parameters on waterflood performance of a two-dimensional, two-layered, field-scale model of a water-wet sandstone system. Particular attention is given to evaluation of the water saturation contours and crossflow rates at the interface between layers to gain improved understanding of the crossflow mechanism. PROCEDURE BASIC: FLOW EQUATIONS The basic flow equations for two-dimensional, two-phase, immiscible, incon~pressible flow in a porous medium are:

Jan 1, 1967

By J. C. Griffiths, D. W. Bennion

A mathematical model, which does not assume a priori that stratification exists, but was designed to test for the stratification was developed. The model segmented the reservoir horizontally into areas of common variance, then divided it vertically into strata (if strata were present). Next, trend surface techniques were used to determine the lateral extent and variation of each stratum. The model was tested on two reservoirs (sandstone and limestone) using porosity as the reservoir rock property. The sandstone reservoir contained approximately 60,000 samples from 2,000 cored wells, while the limestone reservoir had approximately 24,000 samples from 430 cored wells. Within the areas of common variance tested, the model was able to distinguish four separate lithological units or zones in the sandstone reservoir, four in the Marly section and seven in the Vuggy section of the limestone reservoir. INTRODUCTION To accurately predict the movement and production of fluids from a reservoir rock, it is necessary that the reservoir engineer have a knowledge of the rock properties and their distribution throughout the reservoir. For this study, a reservoir rock is defined as a solid containing interconnecting holes or voids which occur relatively frequently and are dispersed within the rock in a regular or random manner. The fraction of bulk volume that these interconnecting voids occupy is called porosity. The rock must also possess sufficient permeability to allow fluids to move through it and it may be composed of one or more strata or lithological units. A stratum or lithological unit as defined in this study is a body or volume of reservoir rock whose properties are so distributed that its lateral and vertical extent can be traced throughout or through a portion of the reservoir. Operationally, the existence of strata are question- able unless the variance within strata is less than among strata. Within the past few years computers have been widely used as a tool for calculating movement and production of fluids from reservoirs. Most prediction models require some type of a mathematical description of certain reservoir rock properties. In the past, most of these models have been relatively simple. Some have assumed vertical variation but no lateral variation, while others have assumed lateral variation but no vertical variation. In general, most of these models have not used functional relationships to predict reservoir rock properties as functions of position. The object of this study was to develop a model which would predict lateral and vertical variations of reservoir rock properties. Since samples are usually available from only a small portion of the total reservoir rock, it seemed logical that if measurements from these samples were to be used to infer the properties of the actual reservoir, the data should be treated statistically as a sample from the total population (reservoir). Therefore, the model developed in this study to predict reservoir rock properties was a stochastic model. The model was tested using porosity (a macroscopic reservoir rock property) measurements from two reservoirs — the first, a sandstone reservoir from which 60,000 samples were obtained; and the second, a limestone reservoir with 24,000 samples. Several investigators have proposed methods to determine the vertical and areal variation of a reservoir rock property. Stiles: Dykstra and Parsons 2 and Suder and Calhoun3 have all developed waterflooding prediction techniques which assume vertical variation but no lateral variation. Stiles developed a method to segment a reservoir arbitrarily using frequency distribution. Law4 suggested that porosity has a normal frequency distribution and that permeability has a log-normal frequency distribution. Elkins and Skov 5 proposed that when a reservoir is segmented vertically, the

Jan 1, 1967

By O. K. Miniato, L. Massé, K. Nobe, J. S. Aronofsky, W. F. 213-000-000-016 Seyer

MUCH work has been done dealing with the effect of mechanical stress on electrode potential in an electrochemical system. The contradictory nature of the experimental results indicates the complexity of the problem although thermodynamic considerations show that a simple relationshir, should exist. In those systems where a gas was the electromotive active substance satisfactory agreement between theory and practice has been found. Des Coudres' found this to be so even when the active substance of the electrode, in this case mercury, was in the liquid state. In contrast, attempts to correlate theory and experiment for the solid state have met with a very limited success. The early workers in this field, Andrews,2 Walker and Dill3 used iron, certainly one of the most reactive of metals. Others have made use of less active metals such as copper and nickel. Recently Fryxell and Nachtrieb4 investigated the electrochemical behavior of gold and silver under both tensile and compressive stresses and concluded that it was doubtful whether true stress potentials could ever be measured. Much of the lack of success to measure the thermodynamic stress potential can be ascribed to the presence or formation of a complex film on the metal surface in contact with the electrolyte. Further, the theoretical stress potential is very small and therefore difficult to measure directly. Thus the calculated emf between a 24 B & S gage cold-drawn copper wire stressed with a weight of 1 kg and an unstressed portion of the same wire is only 2.60 X 10"7 volts. This is very small compared to that which can be produced by chemical reactions at the metal electrolyte interface which in turn can be so large as to mask completely the stress potential. Hence in this type of measurement all chemical side effects must be eliminated or reduced as much as possible. It was for this reason that the system copper-sodium chloride solution was selected for study. INSTRUMENTATION In the many preliminary experiments conducted, two major difficulties were encountered. The first was to measure the small electro-potentials to be expected and the second to obtain a suitable electrode surface. The conventional potentiometric method was found to be unsatisfactory for measuring the small emf expected. However, by using an L & N No. 2290 galvanometer having a resistance of 915 ohms consistent measurements were possible. The reference electrode was always the unstressed one made from the same sample of wire. The steady current flow was approximately 10-8 amp. Lewis and Randell5 have stated that for currents of the order of 10-8, if there is no sensible polarization, the measured emf may be taken as a reversible one. To check the galvanomenter readings an alternative method was devised to measure the potential difference between the wires. This involved a Liston-Falb d-c breaker amplifier model 10, an L & N k-2 potentiometer and a moving-coil galvanometer having a sensitivity greater than 0.1 µv (microvolt) per mm. To increase further the output voltage of the amplifier a d-c amplifier, model B. L.-932 was introduced into the circuit. This amplifier was in turn connected to a Brush recorder which had been calibrated previously by the test signals from the Liston-Falb instrument. These test voltages employed took into account the impedance of the input current. Unfortunately, this method had too low a sensitivity for measurement below 10 µv. Above this value the voltage agreed reasonably well with those obtained directly by the simple galvanometer method. The main advantage of the amplifier setup was that one did not have to wait until no deflection occurred on the galvanometer in the circuit when first exposing the wires to the solu-

Jan 1, 1959

By Milton E. Wadsworth, W. Martin Fassell, William H. Dresher

A study of the rate of dissolution of molybdenite (MoS2) in alkaline solution was carried out under carefully controlled conditions. Effects of temperature, oxygen over-pressure, and KOH concentration were evaluated. Studies were made in the temperature range 100°C to 175°C and in the pressure range 0 to 700 psia of oxygen. Under these conditions molybdenite was found to leach according to a linear mechanism. Both oxygen over-pressure and KOH concentration were found to control the rate of leaching. The mechanism has been explained in terms of adsorption of oxygen at the molybdenite surface followed by configurational rearrangement of the adsorbed molecules. The hydroxyl ion dependency is believed to be diffusion-controlled. Laboratory batch studies have shown that molybdenite can be readily dissolved in alkaline solutions under moderate conditions of temperature and pressure. Commercial application of this process to the production of ferro-molybdenum and molybdenum chemicals is promising in view of the ease of dissolution of molybdenite and the relatively noncorrosive conditions involved in the process. HIGH temperature-high pressure techniques have long been used to great advantage in the organic chemical industry, the petroleum industry, and the paper industry. Only recently, however, have these methods been used to extract metals from their ores on a commercial scale. The Chemical Construction Corp., together with interested producers of nickel and cobalt, has done much to develop methods of producing nickel and cobalt powders by the use of high temperature-high pressure techniques.' The Howe Sound Co. is currently operating a plant near Salt Lake City in which the new Chemical Construction Corp. technique is applied to cobalt-arsenic sulfide concentrates. In this method the concentrates are leached in a dilute solution of sulfuric acid under air pressure at a high temperature. Near Edmonton, in Alberta, Canada, the Sherritt Gordon Co. is also using the new method in conjunction with its ammoniacal leach process.' National Lead Co., at Fredricktown, Mo., is operating a process similar to that of Howe Sound. In spite of the rapid growth of high temperature-high pressure hydrometallurgical processes, there has been very little work done on fundamental principles involved in this type of process. Conse- quently the literature lacks any significant data in this field. Oxidation of pyrite,3 phalerite,4 galena,5 and recently molybdenite" in alkaline solutions has been reported to some extent. This investigation was initiated, therefore, to broaden the application of high temperature-high pressure hydrometallurgy and also to contribute some insight into the basic mechanisms of oxidation in an aqueous medium under these conditions. In addition to the immediate consequences of these processes much valuable information remains to be learned about fundamental reactions when they are carried out at temperatures and pressures slightly higher than those normally encountered. Leaching of molybdenite by alkaline solutions under oxygen pressure has recently been reported in the Russian literature by E. S. Usataya,8 who found that leaching rate increased with an increase in the pH of the solution—the strongest effects being observed at a pH of 10—and also with an increase in temperature. Usataya also has reported the formation of a protective film on the surface of the molybdenite when the leaching solution was weakly alkaline, neutral, or acidic. He believes that this oxidation process explains the migration of Mo+ + in the oxidation zones of molybdenite ore deposits and the subsequent impoverishment of the ores. Equipment: The high temperature-high pressure reaction unit used in this work was especially designed for kinetic studies of this nature, emphasis being placed on accuracy of measurement and precision of control. As details of the unit's construction and operation have been discussed elsewhere,7 Only basic features and principles of operation will be discussed at this point.

Jan 1, 1957

By D. R. Uhlmann, T. P. Seward, K. A. Jackson, J. D. Hunt

microscopic ohservations on alloys of organic trzaterials show that dendrite arms can melt off under normal conditiorzs of growth. This occurs because of the interactiorz of' heat and matter fluxes during dendritic growth. The re melting occurs where the den-drite arms are joined onto the main deizclrite sterrz. Many detached crystals can be produced in this fashion. It is postulated that this remelting phenornenon occurs in metal alloys, giving rise to the equi-axed region in castings. Experiments peyformed orr castings of transparent materials support remelting as a primary source of detached crystals. Ob~ervations an equiaxed tones in metal castings are discussed in terms of this and other mechanisms. It is concluded that the partial remelting of dendrites is on important mechanisnl for producing the equiaxed regions in castings. THE freezing of a casting can be divided into three regions: a chill zone formed near the mold wall, a columnar region, and a third region, at the center of the casting, which is called the equiaxed zone. The origin of the grains that comprise the equiaxed region is the subject of this paper. We will first outline the mechanisms which have been proposed to account for the origin of the equiaxed region and discuss some recent experiments which cannot be explained by these theories. We will then present some microscopic observations of dendritic growth which have led us to conclude that the equiaxed zone in castings can arise from partial remelting of dendrites. This proposal is supported by observations on transparent castings. Finally, we will discuss several observations on metal castings which could not be explained previously, and which can be accounted for by the present proposal. Previous Mechanisms. Winegard and Chalmers3 pointed out that the molten central region of an ingot could be constitutionally supercooled, because of the solute layer at the growing interface. In this supercooled region, nucleation on particles could occur, giving rise to the equiaxed crystals. Another mechanism has also been suggested,4y5 that the nuclei originate in the chill zone then float or are carried by convection to the center of the casting, where they grow to produce equiaxed crystals. In this case, all the crystals nucleate immediately on casting, so this mechanism will be termed "big-bang" nucleation. Walker's Experiments. J. L. Walker has made observations on the solidification of nickel and Ni-Cu alloys which cannot be accounted for by either of the above mechanisms. In studying the grain size resulting from freezing of nickel at various undercoolings, walker6 found that at large undercoolings the grain size was small, due to mechanical nucleation, as discussed by walker7 and Horvay.' At small undercoolings, the grain size was large, and the growth dendritic. In Ni-Cu alloys, however, for initial undercoolings starting from just below the melting point and extending for a hundred or so degrees of undercooling, fine grains were also observed. Samples were undercooled 200 Centigrade degrees without nucleating, and were then heated 130 Centigrade degrees so that the undercooling was 70 Centigrade degrees, and nucleated. The samples had a small grain size, indicating multiple nucleation. There were no heterogeneous nuclei in the liquid which could operate at the temperature of growth. Constitutional supercooling could not have been greater than the supercooling of the initial melt, since the temperature rose as the freezing continued. walker -as also shown that a Ni-Cu alloy which can be undercooled to below its solidus will produce typical columnar and equiaxed regions when cast into a cold mold. This alloy could not reach a temperature below its solidus by constitutional supercooling. It could not, therefore, have nucleated heterogeneously. Neither the big-bang mechanism nor the Winegard-Chalmers mechanism can account for the fine grain

Jan 1, 1967

By W. A. Riggs

In a single year the total transportation cost equals nearly 30 pct of the value of mineral commodities, the largest single cost from the deposit to consumer. The magnitude of this economic factor calls for more complete understanding of cost and operational problems between producer and carrier than now exists. Details are given of the costs of providing transportation as well as freight rates for selling transportation. In 1958, transportation of mineral commodities in the United States required 600 billion ton-miles to move 1 3/4 billion tons of products of mines comprising solid fuels, crude oil, industrial minerals and rocks, and ores. Possibly 17 pct was handled by more than one mode of transport, since combinations of several modes of transport may, at times, achieve better service/cost results than any single mode. Total transportation cost of nearly $5 billion equaled roughly 30 pct of the value of the mineral commodities, the largest single cost from the mineral deposit to the consumer. The tremendous magnitude of this transportation undertaking demands much more complete understanding than now exists between mineral producers and carriers about the economic and operational problems of each other. A substantial portion of the daily work of the writer is spent in trying to act as a combination interpreter and catalyst between potential shippers and carriers, hoping to direct both to points of mutual understanding and advantage. For the purpose of this paper, it is necessary to ask mining people to accept some terminology and to try to appreciate the mental approach of the freight rate making people of the carriers. This paper will consider costs of providing transportation as well as freight rates for selling transportation—although these are fields of limited certainty. There are no accurate statistical breakdowns for all modes of transport and types of carriers indicating commodities, volume of traffic, distances, costs, and rates. Much information is available for railroads, and some for the regulated portions of air, motor, pipeline, and water transportation. Unregulated carriers, handling about half of the transportation of products of mines, are not required to report, and very little is known of their activities. Figures used herein are national in scope, unless otherwise indicated, and have generally been derived from Interstate Commerce Commission reports and files. Tonnage figures have been reduced to net tons of 2000 lb. The very generalized comparison of average mileage freight rate levels for various modes of transport provided by Fig. 1 affords advantageous perspective for the entire field of transportation costs. Dashed guide lines show cents per ton-mile, and dotted guide lines show percentage of first class railroad freight rate. While costs of other than railroad transportation more nearly follow constant cents per ton-mile functions, costs of railroad transportation show characteristic taper, or decrease in cents per-ton mile with increasing length of haul. This fundamental difference in cost is due largely to the fact that railroads and pipelines provide their own fully taxed roadway facilities while highway, waterway, and air carriers use government-provided tax-free roadway at no cost other than fuel, license, and certain excise taxes. Thus railroad and pipeline transportation might be said to carry heavy threshold costs in addition to those transportation costs which are directly variable with ton miles of transportation produced. The original basis of railroad freight rate structures lies in the classification of all articles of commerce into railroad class ralings ranging from 7 to 40 pct of first class (100 pct) rate level, dependent on value, hazard, loading characteristics, service requirements, and whether carload or less than carload. Classification tables and mileage-based (but arbitrarily grouped), rate scales are published as tariffs subject to approval by regulatory bodies. Used together, these determine class rates in cents per 100 lb between points in the U. S. Where local commercial or operating conditions render it advantageous for carriers to depart from

Jan 1, 1961

By Morris Cohen, Robert C. Ruhl

Fe-Ni-B alloys were inresligated by X-ray diffraclion after splat quenching. Although this rapid cooling did not produce a measurable supersaturation of dissol1ed boron in either binary Fe-B or Ni-B alloys, a marked increase in dissolved boron was achieved by the splal quenching of lernary Fe-Ni-B alloys. Boron additions up to 2.0 wl pcl to Fe-13Ni and Fe-24Ni alloys cause an increase in retained austenite from 0 to 59 pet and to 92 pet, respectively. The martensitic phase in the Fe-13Ni-9 at. pct B alloy is .found to conlain about 0.6 at. pet interstitial boron, as evidenced by the tetragonality of this phase, and about 3.6 at. pct substilutional boron, us deduced from the lattice paratrieler decrease, the balance of the boron being precipitated as (Fe,Ni)aR. The austenitic Fe-Ni-B plznses also contain both interstitial and substitutional boron. Iron-Boron System. The phase diagram and related information about the solid solutions and intermediate phases in the Fe-B system are given by ansen,' Elliott.2 and Pearson.1 The equilibrium solid solubility of boron in both ferrite and austenite is quite small: the maximum solid solubility of 0.02 wt pct B (0.11 at. pct B) occurs in iron at the eutectic temperature of 1150°C. while the maximum solubility in a iron is less than 0.01 wt pct.l There is disagreement in the literature as to whether these solid solutions are substitutional or interstitial. Based on the measured activation energy of boron diffusion in iron, it appears likely that boron moves interstitially in austenite. 4 However, this observation does not rule out the possibility that some of the dissolved boron may also occupy substitutional sites in this phase. Investigations of internal friction of boron in iron have suggested that boron is interstitial there.' Shevelev, 5 on the other hand, reports a decrease in the ferrite lattice parameter with dissolved boron content, thus indicating a substitutional solution. Unfortunately. Shevelev's methods and analysis are unclear. Goldhoff and spretnak6 have measured the lattice parameters of pure iron and an Fe-0.005 wt pct B (0.027 at. pct) alloy at both room temperature (ferrite) and from 920° to 1200°C (austenite). They reporte: a lattice contraction in the ferrite of 0.0003 ± 0.0002 due to boron, thus indicating a predominately substitutional solution. Appreciable (0.0010 to 0.0060) lattice contractions were found in boron-containing austenites, but these effects were much larger than could be accounted for by the substitutional solution of all the boron present. Nickel-Boron System. Elliott 2 gives a summary of thephase diagram and recent work on this system. The solubility of boron in nickel reaches a maximum of 0.03 wt pct at the eutectic temperature of 1080°C. Iron-Nickel System. ansen' presents the equilibrium diagram for this system and also discusses the metastable austenitic and martensitic phases along with the a=? transformations. The lattice parameters of Fe-Ni ferrites have been recently redetermined by Abrahamson and Lopata.7 Their data, Fig. 1, show an unusual change in slope at about 1.7 at. pct Ni. Very few measurements of the lattice parameters of Fe-Ni martensites are available in the literature. The values of Roberts and Owen8 are considerably higher than those measured in the course of the present work: they find that a, is constant at 2.874? from 8 to 30 at. pct Ni. Both the slope change in the ferrite parameters and the occurrence of a maximum plateau in the marten-sitic lattice parameters vs composition denote the

Jan 1, 1970

By Frederic L. Kadey

Perlite, as a volcanic glass, has been recognized since the Third Century, B.C. (Langford, 1978). The precise details of discovery often become lost in antiquity, and the variations among the stories pertaining to the more recent discovery of perlite as a material of commerce are no exception. Credit in the United States is given to a dentist who, while experimenting with tooth enamels about 1941, discovered that perlite-the rock-intumesced when subjected to heat. At about the same time it is reported that the chief geologist of Silver and Barytes Ores Mining Co. attempted to put out a picnic bonfire on the shores of Milos Island, Greece by throwing beach sand on it. The ensuing pyrotechnic display immediately conjured up in that man's mind the possibility of a new use for the volcanic rock that constituted most of the island. Very little was done with this discovery either here or abroad until after World War II. Today the name perlite is applied to both the hydrated volcanic glass, generally of rhyolitic composition, and to the lightweight aggregate that is produced from the expansion of the glass after it has been crushed and sized. Petrologically, it is defined as a glassy rhyolite that has a pearly luster and concentric, onionskin parting. Occurrences of perlite are restricted to several Tertiary to Quaternary age rhyolitic belts that trend in a generally north-south direction around the world. Commercially suitable deposits generally occur as domes of several hundred feet in height, although glassy zones in welded ash-flow tuffs and others associated with dikes and sills also have been reported. Mining is by ripping and blasting from open pits. Because of weight considerations, perlite usually is shipped to the local market area for subsequent expanding. In the United States, New Mexico leads in production with Arizona, California, Nevada, Idaho, and Colorado following in approximately that order. The principal use for expanded perlite is as a lightweight insulating aggregate in cryogenics, in plaster, concrete, and in loose fill insulation. Expanded perlite is also used in horticultural applications, and after subsequent milling and classification, as a filter aid. The United States is the world's largest producer and consumer of perlite. Table 1 shows the world production of perlite and Table 2 shows the perlite mined, processed, expanded, and sold or used by producers in the United States. Geology Composition and Morphology Any discussion of perlite must take into consideration its dual nomenclature, for it is known by the same name as both the naturally occurring rock and, after processing and expansion, as the lightweight aggregate of commercial significance. In its naturally occurring form, perlite is a rhyolitic glass that contains from 2 to 5% combined water. While perlite also can occur as andesitic or dacitic glass, these latter types are of negligible commercial significance. Table 3 lists the chemical composition of a few typical perlites (Anderson, et al., 1956; Langford, 1979). What sets perlite of commercial significance apart from other volcanic glasses is the fact that under the proper conditions of preparation-crushing and sizing-it will, when rapidly introduced into a flame of sufficient temperature, expand or "pop." All of the elements of composition contribute to the expansibility of the rock. The role of the combined water, however, is the most significant because it is believed not only to produce a fluxing effect in the softening of the highly siliceous glass prior to expansion, but it is also responsible for the explosive force of expansion through volatilization during heating. The current theory of the origin of the water in perlite is now less con-

Jan 1, 1983

By Stuart S. Forbes

Changes and additions made to the Canadian Copper Refiners Ltd. electrolytic refinery between 1949 and 1955 are reviewed. The effect of high current density on current efficiency and section work is discussed. OPERATING and physical changes which have been made to the electrolytic tank house of Canadian Copper Refiners Ltd. suggest a review of present conditions. Previous papers1 a have described the general arrangement. Since then, expansion, closer anode spacing, and higher current densities have increased annual cathode capacity from 112,000 to 182,000 tons. A recent extension to the tank house, begun in the spring of 1954 and completed in August 1955, was undertaken to handle the monthly production of about 3,000 tons of anodes from Gasp6 Copper Mines. The anticipation of these additional receipts and large stocks of unrefined copper caused by the increase in custom smelting at Noranda made it necessary to increase production without immediately available additional cell capacity. Accordingly, from December 1954 through March 1955, the tank house was operated successfully at a current density of 24.0 amp per sq ft. Again, as of September 1955, one of the two tank house circuits is being operated at this high density. Although other refineries may operate at current densities higher than 24 amp per sq ft, none is doing so with anodes which contain silver and gold content as high as those being refined at Canadian Copper Refiners Ltd. General Arrangement The original building consisted of two parallel bays, each 660 ft long and 60 ft wide, with a 24 ft pump bay extending along the west side of the building. A previous expansion, completed in 1939, was to the west of the original building and consisted of two 60 ft parallel bays 240 ft long. The length of these two bays was extended in 1954 to 540 ft, adding one stripper and 12 commercial sections to No. 2 electrical circuit. Space is still available for an additional six commercial sections and one stripper section. Construction on these seven sections started in September 1955, and will be completed early in 1956. The tank house capacity will then be 206,000 tons of cathodes per year. In the two tank houses there is a total of 900 cells distributed as follows—commercial, 468; stripper, 36; total, 504 in the No. 1 tank house (No. 1 circuit): commercial, 360; stripper, 36; total, 396 in the No. 2 tank house (No. 2 circuit). Section arrangement consists of nine cells to a tier and two tiers or 18 cells to a section. Anodes, weighing 620 lb each, are cast with a Baltimore groove and are refined by the multiple system. Solution enters each cell through a bottom inlet at one end and overflows at the top of the opposite end. Rate of solution flow through the cells is controlled by valves at each section to 4.5 gpm. Electrical power to the tank house is now provided by nine 675 kw motor generator sets. Each set consists of a 135-12 v 5000 amp dc generator, driven by a 980 hp 2300 v synchronous motor. When No. 1 circuit is operated at 22,000 amp, five sets, at 4400 amp each, are connected in parallel. As the maximum allowable current on No. 2 electrical circuit has recently been set at 18,000 amp, only four sets are connected in parallel on No. 2 circuit. A tenth set, now being installed, will be reserved as a spare, for use in either circuit as required. Recent Changes In 1949, the annual capacity of the tank house was increased from 112,000 to 132,000 tons by closing the

Jan 1, 1957

By N. F. Dyson, T. R. Scott, M. R. Thornber, W. E. Ewers, M. Bussell

Leach liquors derived from the processing of nickel ores are generally highly contaminated and contain appreciable free acid. Methods are described for obtaining a commercial grade of concentrate from such solutions using pyrrhotite as the seed material to abstract nick- el, cobalt, etc. from solution. At temperatures in excess of 160° C., recoveries of 99% can be obtained from contaminated solutions where the free acidity is as high as 0.5 M in sulphuric acid. At lower temperatures down to 80° C., high recoveries can also be obtained either by adding H2S to the system with appropriate adjustment of the free acidity or by using "activated" pyrrhotite or artificial FeS in the system without prior addition of H2S. The methods are applicable to liquors derived from either oxide or sulphide ores, and the products are suitable for smelting or other known processes used to obtain pure metals. The mechanism of the reaction appears to vary with the operating temperature, and the results ye therefore discussed in the light of electron probe and optical microscopic studies.

Jan 1, 1973

By W. B. Nelligam, J. Tittman

Refinements in radiation logging techniques during recent years have involved increasing usage of scintillation ditectors. These detectors produce voltage pulses whose heights are related to the energies of the gamma rays which initiate them. Analysis of the gamma-ray spectrum, as indicated by the pulse heights, yields information about the chemical elements composing the formations surveyed. Refined scintillation counter techniques can furnish chemical information concerning earth formations in situ, from a study of the gamma-ray spectra emitted by the formation either naturally or as a result of neutron bombardment."' Accompanying the rising interest in gamma-ray scintillation spectroscopy, there has been increased activity in the development of accelerator-type neutron sources (in contrast to encapsulated chemical-mixture sources). Such neutron generators are attractive for several reasons: (1) they greatly reduce radiation hazards to personnel; (2) there is a great reduction in contamination danger if they are lost in the hole; (3) they can produce larger neutron intensities than can conveniently available encapsulated sources; and (4) they are capable of being pulsed, thus permitting new techniques in logging. In the past, both accelerator and encapsulated neutron sources have been used by others in conjunction with scintillation-detector pulse-height analysis. The results have not been too encouraging, due to the interference among different gamma-ray spectral lines and to the fact that the gamma-ray peaks were not too clearly distinguishable above the large and ill-defined background "noise".'.' This paper is a status report on laboratory studies of a technique using a borehole accelerator as a neutron source, which gives an improved scintillation spectrum, thus permitting more accurate chemical analyses of the formations penetrated. The Schlumberger-accelerator neutron source' is presented; the origins of inelastic and of thermal-neutron, capture gamma rays are dis- cussed, and results are given for some laboratory measurements performed in borehole geometry. THE NEUTRON GENERATOR-TUBE ACCELERATOR In the attempt to develop an accelerator neutron source which would have the desirable properties outlined in the "Introduction" and which would operate satisfactorily under borehole logging conditions, a small-diameter, cylindrical, neutron generator tube has been developed. This tube utilizes the principle of accelerating deuterons (heavy hydrogen nuclei) by a high voltage so that they bombard a tritium (heavy, heavy hydrogen) target. The resulting reactions produce large numbers of neutrons of 14 Mev energy. Furthermore, the tube is permanently sealed and, thus, the use of pumping techniques in the sonde is avoided. The tube consists of a pressure control, an ion source in which the deuterons are stripped of their electrons, an accelerating gap down which the deuterons are sped by the high voltage, a secondary electron suppressor and a tritium-loaded target. Obviously, the tube requires auxiliary circuitry in a sonde for the control of the ion source, tube pressure, high voltage and other operating variables. Neutron yields, both continuous and pulsed, have been produced under simulated field conditions in the range between 1 and 10 times those conventionally used in neutron logging applications. For the experiments discussed in this paper, neutron-pulse repetition rates in the range between 500 and 5,000 pulses/sec are adequate. Furthermore, by making suitable adjustments in operating conditions, one can vary the pulse width from a minimum of several microseconds up to dc. As will be seen later, the present application to well logging does not require that one have available pulses of neutrons which are appreciably shorter than the time it takes for fast neutrons to slow down to thermal energy in water. As a consequence, much of our interest has been directed towards the operating characteristics of the tube with pulses longer than about 10 microseconds in duration. Our experience to date shows that tubes can be operated in this manner with reasonably constant, average neutron outputs.

By P. A. Beck, Hsun Hu

It has been known for many years that in cold drawn polycrystalline aluminum the recrystallization texture is practically identical with the deformation texture.l,2,3 V. Goeler and Sachs4 stated that in cold rolled polycrystalline aluminum, too, the deformation texture is retained upon recrystallization. This behavior was interpreted by Dehlinger9 as an indication that each recrystallized grain inherits the orientation of the matrix in which it grew. However, Burgers and Basart showed6 that in deformed aluminum single crystals the orientation of the recrystallized grains strongly deviates from that of the matrix. Barrett demonstrated8 that even in deformed polycrystalline aggregates the local orientation within each deformed grain changes on recrystallization. No explanation has as yet been offered of how the aggregate texture can be retained, while the local texture is everywhere changing. According to Burgers and Louwerse6 the orientation change on recrystallization in compressed and rolled aluminum single crystals corresponds to a rotation around [112] axes lying in the active slip planes and perpendicular to active slip directions. This orientation change was rationalized by them on the assumption that the orientation of the recrystallized grains is determined by the orientation of the available nuclei, and that these nuclei are small fragments of the deformed crystal, rotated in the deformation process. Barrett pointed out,? however, that these assumptions were by no means proven, and that the total volume of material necessary for the nuclei is so small, that it must be available in any orien- tation whatever. It is, therefore, unlikely that an "oriented nucleation" theory could satisfactorily explain the orientation changes in recrystallization of a deformed crystal. Furthermore, in contradiction to Burgers and LOU-werse's conclusions, Barrett's results for the orientation change could be best expressed in terms of rotations around. [Ill] axes. Thus agreement is lacking not only in the interpretations but apparently even in the experimental results contributed by the various investigators. The orientation relationships on coarsening* in a highly oriented polycrystalline matrix were first investigated by Burgers and Basart.5 They produced a fine grained highly oriented matrix by the recrystallization of a compressed or rolled single crystal of aluminum, and studied the orientation relationships in three successive generations of crystals: the "deformation texture" in the single crystal, the recrystallization texture, and the coarsening texture. Burgers24 showed that the preferred orientation of each successive generation was almost always widely different from that of the preceding one, but that the coarse grains often approximately reverted to the orientation of their grandparent, the deformed single crystal. This observation, and the idea that the orientation of the coarse grains is determined by that of the available "nuclei," led to the concept that the coarse grains are nucleated by the remnants of the deformation texture.12,15 On the other hand, Bowles and Boas16 found, in a carefully conducted experiment, that in recrystallized fine grained copper of cube texture coarse grains grow in orientations which can be derived from the orientation of the recrystallized matrix by rotation around a [lll].] direction: the coarsening texture here does not appear to be related in any simple manner to the original rolling texture from which the cube texture had been obtained by recrystallization. It may be assumed that in a recrystallized material, even with a strong texture, there always are present some grains of practically any orientation. These may serve as "nuclei" for the coarse grains, provided that the conditions are favorable for their growth. The existence of a coarsening texture may be considered as an indication that grains with certain relative orientations with respect to the preferred orientation of their neighbors can grow much faster than others. This "oriented growth" theory was briefly suggested by van Arkel, as early as 1936,13 and it was mentioned by Burgers." Recently, C. G. Dunn produced direct

Jan 1, 1950

By E. Topanelian

In recent years considerable progress has been made in the development and application of mathematical techniques for the solution of certain problems involving economic "strategies". Such a problem might involve, for example, the scheduling of shipments of a commodity from a number of sources to a number of destinations. The object would be to schedule the shipments in a manner so as to satisfy the destination requirements and at the same time minimize the transportation costs. The solution to such a problem is not necessarily intuitively obvious. The "obvious" solution is frequently far from optimum. If the shipments are to be made from, for example, only two sources to four destinations, the optimum schedule is readily found. However, if shipments are to be made from, say, 10 sources to several hundred destinations, even a competent and experienced scheduler may spend considerable time in finding a reasonable answer. Even then he is not sure that he has the optimum solution. Furthermore, he has no way of knowing how far from optimum the answer is. Consequently, he does not know whether he should accept this solution or seek a better one. Prior to the advent of large high-speed digital computers, little more could be done with such problems because of their great size and multiplicity of possible solutions. A problem involving 20 sources and 50 destinations would require choosing, from a very large number of possible combinations, the optimum combination of 1,000 variables. The best one could do was to utilize intuition, extrapolation from past experience, and other non-exact approaches. With a high-speed computer, however, such problems can be solved providing a reasonable computational procedure (or algorithm) can be utilized. The purpose of this paper is to describe such a procedure (linear programming) and to apply this procedure to a production scheduling problem. THE RESERVOIR PROBLEM A simple reservoir model is used throughout this analysis to illustrate the use of linear programming. Even the simplest reservoir behavior problem is nonlinear in both space and time, but if the geometry is fixed for a particular study and the time variable is quantized, the resultant system may be described by linear constraints on the variable production rates. Crude oil is available from five separate sources and is delivered to a pipeline. Sources 1, 2, 3 and 4 are ideal reservoirs and therefore are subjected to reservoir flow restrictions. Source 5 is labeled "Outside Source" and crude oil from this source is assumed to be available in unlimited quantities without considering reservoir conditions. The general problem is to determine the schedule of crude oil production from five sources which, over an eight-year period and subject to certain restrictions, will result in maximum profit. "Profit" is defined to encompass all economic factors and expenses involved in producing and selling crude oil to a pipeline facility. Such economic factors are lumped to the extent that the term represents the dollars profit from one barrel of crude oil from any of the five sources entering the pipeline system. Table 1 presents the assumed profit per barrel for oil from any of the five sources over each of the four time periods. In this chart the eight years is broken into four equal intervals of two years. The selection of four time periods of two years each and the values representing the potential profit are completely arbitrary selections for the purpose of illustrating this idealized reservoir problem. In any practical application of this work a careful economic study would have to be made in order to estimate potential unit profits for time periods as far in the future as eight years. In this particular study it is assumed that all of the potential unit profits (C) are known and fixed before the production schedule is attempted. For each reservoir arbitrary values are assigned for

By J. Washburn

Two simple types of dislocation distribution were introduced into zinc crystal specimens and the effect of each on the stress-strain curve was investigated. Quantitative results were obtained for simple edge dislocation arrays and for an array of screw dislocations lying in the slip plane. A CCORDING to present knowledge, the disloca-tions present in large annealed metal crystals can be divided into two somewhat arbitrary groups: 1—single dislocation lines distributed more or less at random or forming elements of a three-dimensional network in which the distance between adjacent dislocations is of the order of 10 2 to lo-' cm and 2— widely separated planar arrays of edge dislocations forming dislocation walls or small angle boundaries within which adjacent dislocation lines are spaced at much smaller distances (lo-' to 10- hm). The former can be considered as a dislocation interpretation of the mosaic crystal proposed by Darwin and Ewaldl, ' 40 years ago to account for anomalously high integrated intensities of X-ray diffraction maxima. Small angle boundaries, although now known to be present in most single crystals used for mechanical testing, were not generally recognized by the early workers. This was partly due to the fact that only recently have improved X-ray and metal-lographic techniques been available for checking the macroscopic perfection of crystals."" It has long been known that changes in growth conditions and in annealing procedure, which might logically be expected to cause variations in the structural details of both the dislocation network and of dislocation boundaries, produce marked variations in some mechanical properties such as yield strength." However, no quantitative experimental correlations between changes in dislocation distribution and changes in mechanical properties have yet been made. Such a correlation has been difficult to obtain because, even when great care is exercised to keep the histories of a number of single crystal specimens identical, it usually has not been possible to avoid considerable variation in macroscopic per- fection.' The number and orientation of dislocation boundaries vary from specimen to specimen. This has probably been an important contributing factor to the large scatter in the results of most mechanical measurements on pure single crystals. Some recent experiments"% ith single crystals of zinc have shown that the presence of dislocation boundaries in a specimen can increase its resistance to deformation by slip. With polycrystalline aluminum and nickel, there is also evidence that dislocation boundaries within the individual grains of the aggregate can increase the resistance of the material to plastic deformation, either as measured by tension tests at room temperature or by creep tests at higher temperatures.'" " Although the foregoing observations seem to have established the fact that substructure can have a strengthening effect, the test conditions were too complex to give much information concerning the mechanism. In the foregoing cases, a network of intersecting boundaries having various orientations and boundary angles were present. Before their apparent strengthening effect can be understood, it will be necessary to isolate and study separately the effect of a number of variables: 1—boundary angle, 2—boundary orientation with respect to the active slip direction, 3—number of boundaries, 4—intersections of boundaries, 5—detailed structure of the boundaries, and 6—interaction of impurity atoms with dislocations in boundaries. The object of the present work was to study the effect of dislocation boundaries on flow stress under the following simple experimental conditions: 1— substantially pure shear deformation and 2—boundaries of controlled angle, orientation, and number. In this way, it might be possible to distinguish the important variables from the relatively unimportant ones. Experimental Procedure Stress-strain curves of hexagonal metals are generally nearly linear even out to very large strains."

Jan 1, 1956

By J. Handin

Triaxial compression tests with independently applied external confining pressures and internal pore pressures show that the ultimate compressive strengths of representative oil well cements are nearly linear functions of effective pressure — the difference between external and internal pressures on the jacketed cylindrical specimens (to 15,000 psi). The strengths are little affected by the test temperature to 350F (not to be confused with the curing temperature). At an effective pressure of 15,000 psi, strengths are in the rage of 30,000 to 50,000 psi, comparable to those of sedimentary rocks under similar conditions. The cements become very ductile even under low effective pressures; permanent shortenings of 30 per cent or more are attainable without rupture. INTRODUCTION Since the pioneering work of Richart, Brandtzaeg and Brown1 on the failure of cement under combined compressive stresses, it has been recognized that ultimate compressive strength is greatly enhanced by the application of confining pressure. More recently, Mc Henry2 showed that the strength of concrete was a linear function of the effective pressure (the difference between the external confining pressure on a jacketed specimen and the internal fluid pore pressure), at least for a range of 0 to 1,500 psi. The effect of temperature had not been investigated, and no previous systematic triaxial compression testing of naterials used for oilwell cementing seems to have been done. The present work was suggested by the late J. hi. Bugbee3 who stated that "consideration of the common application of high-pressure hydraulic fracturing to the initial completion or recompletion of wells, and the large pressure drawdowns in some producing wells, particularly those in abnormally high-pressure gas-condensate reservoirs, raises the question of what is a suitable cement strength for various completions. The intuitive belief exists that cement strength need be no greater than formation strength. Tests should, however, be conducted at downhole conditions." The ultimate compressive strengths of rocks penetrated by the borehole must rise several fold with increasing depth.4 This marked enhancement of strength is due to the influence of the effective pressure, the total weight per unit area of the overburden less the hydrostatic pore pressure. (The effect of temperature due to the geothermal gradients is relatively small for depths to 30,000 ft.) .A significant comparison of the strengths of rocks and cements at downhole conditions requires knowledge of the confined compressive strengths of cements as well. EXPERIMENTAL PROCEDURES The theory and technique of triaxial compression testing are fully discussed in earlier reports.4-6 Briefly, cylindrical specimens 1-in. long and 0.5-in. in diameter are jacketed in thin copper tubes of negligible strength, placed in the test chamber and subjected to an external confining pressure of kerosene and loaded axially by the piston at a strain rate of 1 per cent per minute. Pore pressures of water (or kerosene) are applied independently through the hollow piston and are maintained constant during the shortening of the specimen, Tests at sensibly 0 pore pressure are arranged so that any free water in the cement can escape to the atmosphere. (If egress of water were denied, pore pressure would rapidly attain the value of the external confining pressure because of reduction of pore space.) The test chamber can be heated for high-temperature experiments. Unless otherwise noted, the cement samples were air dried for about a week. Recorded during a test are pore and confining pressures, shortening and axial differential force (total force less the product of the confining pressure and the area of the piston). True stress-strain curves are constructed by dividing the measured differential force by the actual cross-sectional area of the specimen at a given

Jan 1, 1966

By Martin Weinstein

A technique is described for preparing finegrained lead telluride by ultrasonic agitation of a solidifying melt. Material prepared by this technique is dense and chemically homogeneous. N-type PbTe, containing 0.03 mole pct PbIz, has been made and its thermoelecCric Properties have been measured as a function of temperature. For comparison, the properties of similarly doped PbTe made by cold pressing and sintering, and by extrusion, have also been measured. The ultrasonically prepared material compares favorably with the others in its thermoelectric-efficiency factor. Comparison of compressive-flow curves for the three kinds of PbTe show that the ulhasonically prepared material has much superior ductility. The cleavage strength of the ultrasonic material is related to the grain size, D, by the Petch relation:Extrapolation to infinite grain diameter yields a fracture strength of 5000 psi for single-crystal PbTe. WHEN metals and semiconductors solidify in a mold they normally assume one of three cast structures illustrated in Fig. 1.' Solidification in a casting starts at the mold walls where a large number of fine crystals of random orientation can be nucleated to form the chill zone. Because of the anisot-ropy of the growth rate, those crystals whose direction of maximum linear growth is parallel to that of the heat flow grow faster and crowd out the crystals of less favorable orientation. A second zone, having a preferred orientation, called the columnar zone, thus forms adjacent to the chill zone. The speed of growth of the columnar grains will depend, in the case of limited undercooling of the melt, on the rate at which heat can be abstracted. The columnar zone can extend to the center of the casting, Fig. l(a), but it is frequently followed, in solid-solution alloys, by another zone of equiaxed randomly oriented grains in the central portion of the casting, Fig. l(b). The equiaxed structure in Fig. l(c) represents the completely grain-refined case where the equiaxed grain size is small. The third type of structure is the most desirable because it imparts a somewhat higher strength for all except high-temperature applications, it reduces segregation of the doping constituent, and it reduces the possibility of hot tearing (the separation of grains due to the melting of a low-melting point constituent in the grain boundaries). In order to obtain fine-grained castings, the nu-cleation frequency must be increased and grain growth must be restricted. Various techniques have been employed for obtaining this end, namely: rapid cooling, vibration, and inoculation of the melt. The success of these techniques depends upon the characteristics of the metal species and on factors controlled by heat transfer through the crucible walls. Recent studies2" have shown that the application of ultrasonic energy to the solidifying ingot is an extremely powerful tool in the improvement of the crystalline structure of metallic castings. Both the mechanical properties and homogeneity of the ingots are improved. Ultrasonic oscillations may affect the crystallization process by 1) permitting subcritical nuclei to agglomerate and thus form nuclei of sufficient size to cause crystallization, 2) changing the state of surface adsorption of various catalysts found in the liquid melt, 3) breaking pieces of solid from the solidified surface near the supercooled region thereby increasing the number of possible nuclei, 4) causing temperature fluctuations to occur in certain parts of the melt thereby increasing the supercooling at specific points in the liquid, and 5) decreasing the critical nucleus size by increasing the pressure at specific points in the melt.' Various investigators have concluded that the effectiveness of the ultrasonic oscillations results from cavitation which disrupts the growing solid-liquid interface The present paper describes the application of ultrasonic oscillations to the crystallization of the semiconductor N-type PbTe. The purpose of this study is to prepare crystalline

Jan 1, 1964