Search Documents

[VOL. XXXVI. Page. Line. 155 29 For "Joachimstahl," read "Joachimsthal." 215 Foot-note 2. For " May, 1892," read " May, 1902." 216 21 For " ack-screw," read " jack-screw." VOL. XXXVII. 31 3 For "quantity of tons," read "quantity of slimes." 35 10 Expunge "recorded in Table VII." 37 24 Expunge "to." 38 33 For "page 89," read "page 9." 44 40 For "page 86," read "page 6." 47 In table, third line under heading "Excavators and Conveyors," expunge "per 40 ft. of."]

Jan 1, 1918

By Effingham Humphrey

THE Lehigh Valley. Coal Co. finished the rebuilding of its Drifton No. 2 breaker at Drifton, Pa., in the summer of 1917. The new construction comprises an addition and the complete remodeling of the old breaker. It is of interest to note that the old structure was the first iron breaker erected in the anthracite region. THE OLD BREAKER This old breaker was built by the Cross Creek Coal Co., under the direction of the late Eckley B. Cole, in 1888-89, and was fully described by him in the Transactions.1 The columns were cast iron, 8,'10 and 12 in. square. The floors and partitions in pockets were cast-iron ribbed plates. The struts were cast iron of "H" section; the other members were of structural iron either rolled I-beams or built-up sections. The sizes of the rolled beams varied from 6 to 20 in. deep, while the built-up sections, made of plates and angles, varied from 6 to 63 in. in depth, so that there apparently was no rule to determine the type of section used. In the remodeling of the old structure, practically everything was taken clown excepting the columns and roof, and such beams as were necessary for temporary construction purposes, and, therefore, a close inspection of the old structural members could be made and the effect of the acid water oil them could be noted. The cast-iron members were but slightly attacked by the water, while the wrought-iron beams, in the wet places, were corroded almost to failure.

Jan 2, 1918

By William P. Lohden

INTRODUCTION It is recognized that, for a variety of reasons, some companies in the mineral industry today are by no means cash-rich and, in fact, are reporting a growing proportion of long-term debt in their capital structures. A review of recent balance sheets of small, medium-size, and some larger companies, indicates that a fair number still have substantial positions in cash equivalents such as U.S. government issues and other short-term money market instruments. In part, this paper concerns itself with companies which have sufficient cash and equivalents and/or cash generation to internally finance mining projects or expansions but which, for some reason, choose to borrow funds. Misconceptions which appear to frequently underlie so-called "leveraging" decisions are explored in this paper. Also considered are those circumstances under which any company, including one that is cash-rich, should consider borrowing for a project in an amount beyond what would otherwise be necessary based upon its internal financing ability. I do not 'attempt to cover the raising of equity capital in public markets in this paper. OVERALL RETURN ON TOTAL POOL OF INVESTABLE CASH SHOULD INFLUENCE FINANCING DECISIONS If you approach an individual with an investment which can be financed from his savings, or by borrowing at a rate higher than he is earning on his savings, he will quickly tell you that to pay interest at a rate higher than he is earning would reduce his overall income. Assuming he is not currently considering any additional investment

Jan 1, 1977

THE Institute of Metals Division of the American Institute of Mining and Metallurgical Engineers appointed a Research Committee in 1925 to de-termine what could be done by the Division to promote research work in the United States on non-ferrous metals. It was recognized that a considerable volume of use-ful research work in this field was being carried on by individual industrial companies as well as by the uni-versities and other research institutions, such as the Bureau of Standards. One need only refer to the recent research literature on non-ferrous metals in the TRANS-ACTIONS of the A.I.M.E., and elsewhere, to be con-vinced of healthful research activity in this field. The appointment of the Committee, however, voiced the impression that what was being done was, however excellent, inadequate for the needs of the industry. It was felt that the Division could usefully devote some of its time and effort in stimulating activity in this field. The deliberations of the Research Committee have not failed to develop wide differences of opinion even on the simple questions: (1) whether the Division can aid in any practical manner in this cause and (2) what the features of such aid might be. However, it was clear that there was only one type of research activity with which it could be very usefully concerned, viz., that on subjects of fundamental interest and general application. It was obvious that research work having special objects and more immediate commercial appli-cation should best be left to the industry itself.

Jan 1, 1927

I HAVE told you of two parts of the mould for guns. You lack the third, which is the one for making the breech. This, in addition to being a part that is always ornamented with some piece of sculpture to make the gun beautiful, is that part which forms the bottom and closes the whole mould. It is also the one that sustains the entire burden of the bronze, and it must therefore be made with great consideration and diligence, taking care to make it strong with clay and with iron bands. Various methods are used in making this. Every master does as he knows how, either preferring to do it quickly or delighting to make his work ornate and beautiful. His choice also depends on whether they are to be just artillery or occasions for artistry. There are some who, if the guns are of a round form, make the pattern for the breech on a lathe, either of wood or of clay. If they are fluted, they make the flutes by hand in wood or clay, following the pattern of the board. In a part that perchance might not come out of the mould, they put some tallow underneath or make it entirely of tallow or wax so that it will come out. Likewise, if they wish to make cornices or other projections these can be put on either in wood or in clay. In the same way they also apply leafwork of clay or wax so that it can be taken out by hand or with the fire.

Jan 1, 1942

By Arthur C. Spencer

Having suggested magmatic waters as the probable agents of vein- and ore-deposition in Southeastern Alaska in a paper entitled, The Geology of the Treadwell Ore-Deposits,' it is with particular interest that I note Mr. W. Lindgren's application of the hypothesis of igneous emanations to the gold-quartz veins of Victoria and of California. After describing the similarities of the veins and of the changes in the wall-rock due to the action of vein-waters in the two regions considered by him, Mr. Lindgren formulates the hypothesie that the veins of this type " have been deposited chiefly by ' eruptive after-effects ;' in other words, chiefly by hot ascending waters originally contained in the granitic magma and relased from it by decreasing pressure, due to its irruption into the upper parts of the litho-sphere. It is quite possible that atmospheric waters may have played a certain part by aiding the precipitation and by effecting certain forms of concentration in the deposits." There are many reasons for extending this hypothesis to southeastern Alaska. This region and the Sierra Nevada belt of California are undoubtedly parts of one geologic province, throughout which the main events of geologic time are evidenced by identical or closely similar records in the rocks. Our knowledge of the former region is still fragmentary, to be sure; but the origin-dates of the most prominent features of geology have been located in the time-scale, and found to correspond completely with the red-letter dates in the Californian record. In both there are: (1) intense folding and meta-

Jan 1, 1906

By E. Gybbon Spilsbury

It is not my purpose in this paper to describe all the different contrivances which have been devised, during the last quarter of a century, for the purpose of Iessening the expense of mining and tunnelling operations; I wish merely to call your attention to the crying want of the Western miners for some cheap and effective machine, capable of economizing on the heavy item of hand-drilling, and to enumerate a few of the latest improvements which have been made in machines of this class. This necessity for the introduction of some kind of labor-saving machinery in mining, especially in the West, begins to make itself felt more imperatively every day. No branch of industry has remained so conservative to the old customs and systems of working, as has mining; and yet no branch is so entirely dependent on economical working for a successful issue; and in very few is the proportion of cost of hand-labor to profits obtained so preponderantly heavy. Perhaps the chief reason for this seeming apathy towards progress in this direction arises from the fact that nearly all mining operations, especially in this country, are carried on in regions more or less remote from the great centres of civilization, thereby rendering the carriage and erection of machinery extremely difficult and expensive. Another reason, however, exists in the fact that a large number of men in charge of mining operations are greatly prejudiced against the introduction of machinery underground, from the idea that it cannot be made to adapt itself to the various positions and

By D. K. Das, P. A. Beck, S. P. Rideout

IN a previous publication1 1200°C isothermal phase diagram sections were given for the Cr-CO-Ni, Cr-Co-Fe, Cr-Co-Mo, and Cr-Ni-Mo ternary systems, in which the a phase formed narrow, elongated solid solution fields. The present investigation is concerned with the 1200°C isothermal sections of the Co-Ni-Mo, Co-Fe-Mo, and Ni-Fe-Mo ternary systems. A prominent feature of these systems is the presence of narrow, elongated µ phase fields. The crystal structure of the phase designated as µ both here and in the previous publication1 was determined by Arnfelt and Westgren.2 For the (CO, W)µ phase, named by them Co,W, (and also frequently designated as a), these authors found that the crystal system is hexagonal-rhombohedra1 and the space group is D53d — R3,. Westgren and Mag-neli3 later found that isomorphous phases exist in the Fe-W and the Fe-Mo systems (these phases are often referred to as < and E, respectively). Henglein and Kohsok4 stated that the phase described by them as Co7Mo,; (otherwise frequently designated as c) is also isomorphous with the above three. The Co-Fe-Mo system was investigated at 1300°C by Koester and Tonn,5 who found a continuous series of solid solutions between (Co, MO)µ and (Fe, MO)µ Koester6 also indicated similar uninterrupted solid solutions in the Ni-Fe-Mo system. However, since the Ni-Mo binary system does not have a phase isomorphous with F, Koester&apos;s diagram is expected to be erroneous. No data appear to be available in the literature concerning the Co-Ni-Mo system. The face-centered cubic (austenitic) solid solut,ions of iron, nickel, and cobalt, which are quite extensive in all three systems at 1200°C, are here designated as the a phase. The body-centered cubic (ferritic) solid solutions, based on iron, are designated in this report as the ? phase, in conformity with the nomenclature used previously.&apos; Experimental Procedure The alloys were prepared by vacuum induction melting in zirconia and alumina crucibles. The lot analyses for the metals used have been given.&apos; The number of alloys prepared was 46 for the Co-Ni-Mo system, 65 for the Co-Fe-Mo system, and 113 for the Ni-Fe-Mo system. The compositions of these alloys were selected with due regard to maximum usefulness in locating phase boundaries. The alloy specimens were annealed at 1200°C in an atmosphere of purified 92 pct helium and 8 pct hydrogen mixture. Alloys consisting almost entirely of the face-centered cubic austenitic a phase, or of the body-centered cubic ferritic c phase were double-forged with intermediate annealing. The double-forged specimens were then final annealed for 90 hr at 1200 °C and quenched in cold water. Alloys containing considerable amounts of any of the other phases could not be forged. Such specimens were annealed for 150 hr at 1200°C and quenched. Microscopic specimens of all alloys were prepared by mechanical polishing, in many cases followed by electrolytic polishing. Description of the polishing and etching procedures used and tabulation of the intended compositions of the alloys prepared are being published in two N.A.C.A. Technical Notes.7,8 , Many of the alloys were analyzed chemically and, in general, the results are in excellent agreement with the intended compositions. X-ray diffraction samples were prepared by filing or crushing homogenized alloy specimens and by reannealing the obtained powders in evacuated and sealed quartz tubes. After annealing for 30 min at 1200°C the tubes were quenched into cold water. X-ray diffraction patterns were made with unfiltered chromium radiation at 30 kv, using an asymmetrical focusing camera of high dispersion. X-ray diffraction and microscopic methods were used jointly to identify the phases present in each specimen. The amounts of the phases in each alloy were estimated microscopically. The phase boundaries were located by the disappearing phase method. The results were used to construct 1200°C isothermal sections for the three ternary phase diagrams. The accuracy of the location of the phase boundaries determined in this manner is estimated to approximately ±1 pct of each component. The portion of the three phase diagrams lying between the µ, P, and 6 phases on the one hand, and the molybdenum corner on the other, has not been investigated. Recently Metcalfe reported0 a high temperature allotropic form of cobalt on the basis of dilatometric results and of cooling curves. In the present work no attempt was made to search for the new phase in the cobalt corner of the Co-Fe-Mo and Co-Ni-Mo systems. No alloy was prepared with more than 80 pct Co; the alloys used were intended to locate the boundary of the a phase saturated with cL. The microstructures of the quenched a alloys near the cobalt COrner gave no suggestion of an in-suppressible transformation On quenching. The location of the boundaries of the a + ? two-phase fields in the Fe-Ni-Mo and Fe-CO-MO systems was determined entirely by the microscopic method. The face-centered cubic a alloys near the ? field transform partially or wholly into the body-centered cubic ? phase on quenching from 1200°C to room temperature. The ? formed in this manner has an

Jan 1, 1953

By R. P. Rothwell

THE first difficulty mentioned is that in some instances two or more beds of coal separated by sandstone or slate rocks of considerable thickness in one part of a basin, are found running together in another part. Of course, we may happen to strike first the part of the basin where there is but a single seam, and in this case the bed would appear 60 divide into two or more branches within a short, distance. Such cases are not rare in the anthracite coal-fields. I would suggest as an explanation of this phenomenon the gradual sinking of the peat-marsh-the embryo coal-bed-on one side, and the moving forward of the marsh, so that on one part of the bed the formation of peat would still be progressing, while another part, being under water, would be covered with mud and sand. Thus we have different portions of the same bed of different ages. Now if the sinking of the marsh be stopped for a time, the bed will become thicker in the portions left exposed, and if the sinking now changes in direction, so that the part that had previously gone down commences to rise, we should have the phenomenon of a bed, continuous throughout, with one portion overlying another, and separated from it by rock strata. These are exactly the conditions observed in splitting beds. While one side of the lake is sinking, and the peat marsh moving on in that direction, the other side may be rising,

By R. W. Raymond

WISH to call the attention of the Institute to a curious subject, brought to my notice last summer by Mr. Begger, the accomplished metallurgist of the smelting-works of the Boston and Colorado Company at Black Hawk, near Central City, Colorado. At these works, the richest auriferous sulphhrets of Colorado (particularly copper pyrites) are smelted in reverberatories, together with roasted tailings (iron pyrites), and the gold and silver are concentrated into a new, artificial sulphide, or copper matte, containing $1500 and upwards of the precious metals per ton, and this is shipped to Swansea. I will say in passing, that this shipment of an unrefined product, like the similar shipments from Utah and Nevada to San Francisco, Chi¬cago, St. Louis, Newark, New York, and Europe, of crude argentiferous lead or "base bullion," is not a sign of incomplete metallurgy here, but has a sound business reason. The separation of the precious metals in the West would be more expensive, to begin with ; and then it would necessitate the movement of these metals by express, at high rates and risk, to commercial centres or coining mints, while the base metals having no home market, must be shipped and sold at little or no profit. At present, the gold and silver, safely packed, as it were, in the base metals, are transported with safety as ordinary freight; and the base metals probably more than pay cost of shipment and separation. To return to the Black Hawk reverberatories. On a recent occa-

Jan 1, 1873

By R. V. Whetsel, V. R. Garfias

THE present study is intended as a preliminary statistical survey of the world&apos;s production of petroleum substitutes. The information presented is admittedly deficient. It is believed, however, that the increasing importance of these substitutes, particularly with Europe at war, justifies its presentation at this time, if for no other [ ] reason than to encourage enlightened pertinent discussion. The world&apos;s production in 1939 of petroleum substitutes-of which approximately 97 per cent are direct substitutes for motor fuels-is tentatively estimated at 108,000,000 bbl., or equivalent to the combined output of crude oil in 1939 of Rumania, Mexico and Colombia. With few exceptions, these figures of production represent also actual figures of consumption. The United States, owing mainly to its output of natural gasoline, leads all countries in the production of these products, with about 53 per cent of the total. In European countries, particularly Germany, the imminence of war in 1939 forced an increase in production and improvement of methods of manufacturing motor fuels, largely from coal, with the result that this country produced in that year over 20,000,000 bbl. of substitutes. Since the beginning of hostilities, substitutes have offered more and more the means of meeting the unfavorable balance between supply and demand in European [ ] countries; the increase in production of these products being at least in part offset by the systematic bombing of synthetic plants and oil storage. The source materials and the resulting substitutes are listed in Table I. The following are the approximate gross heat equivalents of some substitutes to barrels of gasoline:

Jan 1, 1941

CHARLES CATLETT, Staunton, Va. (communication to the Secretary*). -I hesitate to discuss in general terms a paper such as Mr. Wysor&apos;s, which bears evidence of so much careful and detailed investigation, yet it is the broad possibilities which his paper presents that are really attractive and his cautious conservatism may make us unappreciative of these possibilities. Mr. Wysor calls attention to the fact that the iron-ore mixture which he uses, carrying 0.28 per cent. of potash, is probably above the average. No doubt this is true, but on the other hand it may be very much less than the mixture at some blast furnaces or very much less than would be the case with special mixtures bearing the question of potash in mind. Unfortunately, iron ores are not ordinarily examined for potash, and with the ordinary analyst there is opportunity for very considerable error in the determination. The 10th Census gives 270 complete analyses of iron ore, on the accuracy of which we may rely. Of these, there are 21, or 8 per cent., that carry more potash than Mr. Wysor&apos;s mixture; 14 of these carry approximately twice as much, or more; eight carry approximately three times as much, or more; three carry approximately five times as much; one carries over seven times as much. It may be worth while to take some of the ores that are known to be high in potash and consider the possibilities in the light of Mr. Wysor&apos;s investigations.

Jan 5, 1917

not weaken. I saw him shortly before he was killed; his conduct under fire was splendid and an inspiration to his men. His loss is felt deeply by all ranks. Thanks to him and to others, who like him, paid the full measure of devotion to their country, our line was held until the critical situation in that vicinity was at an end. He died the true death of a soldier, with his face to the enemy. As we now look back, it is easy to believe that this holding of the line of defense intact by General Carey and his men was a determining factor in the outcome of the war. To have played so important and noble a part in this vital effort as that taken by Perry is assuredly the privilege of few. Our lives, it seems, are like capital entrusted to us to be expended as wisely and effectively as we may. With them we purchase whatever of accomplishment the stuff that is in us permits. It is impossible to escape profound regret that a career so full of the highest promise, and a personality so overflowing with all that is fine and lovable, should have been cut short at the age of thirty-one. Yet who can doubt that in a few months Perry bought with his life the fullest achievement of a life-time—a glorious part in the salvation of Liberty and Justice and Decency, indeed of Civilization itself! L. C. Graton.

Jan 1, 1920

By S. J. Aresco, George E. Keller, J. Visman

INTRODUCTION The accurate sampling of coal, as with most minerals, is a difficult task. Coal is a very heterogeneous material made up of different types of coal and varying amounts of mineral matter. The product as mined may contain all of the layers of coal and impurities found in the seam as well as portions of the strata above and below the coal seam. The preparation plant is the device to size, crush and/or remove impurities so that the coal may be shipped as a saleable product. Sampling may be needed at many stages in the preparation process. Although this chapter is mainly concerned with sampling in connection with preparation processes, the principles will apply to all coal sampling. The main reasons for sampling in connection with coal preparation are: 1. To determine the washability characteristics of the raw coal by means of float and sink tests. These may be used for the design of a preparation plant, prediction of results to be obtained or for monitoring raw coal delivered to the plant. 2. To check the performance of various operating units in the plant, either by float and sink tests or chemical analyses. 3. To determine the analytical characteristics of the products produced, such as moisture, ash, Btu, sulfur, etc. HISTORY The earliest accepted methods of sampling coal in the United States were given in U. S. Bureau of Mines publications by J. A. Holmes,1 G. S. Pope2 and A. C. Fieldner.3 The American Society for Testing and Materials more or less adopted the methods proposed by the U.S. Bureau of Mines in their Standard D-21-1916, and it remained a standard for many years. Briefly, the standard called for a 500 pound sample for coals less than. 3/4 -in. in size and a 1,000 pound sample for all coals over ?4 -in. in size. No mention was made of increments but there was an instruction that the sample should spread over the coal to be sampled. Sample preparation was by hand crushing with the alternate shovel method for reduction to 250 pounds followed by coning and quartering below 250 pounds. Obviously, with the amount of work involved, this method of sample preparation was rarely followed. This method of preparation resulted in samples that were practically air dried because of long exposure while crushing, shoveling and quartering. In the late nineteen twenties and early nineteen thirties, studies for more practical methods were begun. Dr. E. S. Grummell4, Imperial Chemical Industries, Ltd, London, summarized the work to date at the

Jan 1, 1968

By Mark R. Lamb

The various methods of treating pulp in air-agitation tanks offer problems for experiment and study which are fascinating as well as practical. The usual method heretofore has been to fill each tank in turn, agitate the mixture the required period and then discharge the treated pulp into a storage-tank, from which it is drawn to the filter as required. A later method is to run the pulp from the tube-mill, classifier, thickener, or settler into the first of a set of tanks, and thence continuously or in series through the remaining tanks, finally drawing off the pulp to a continuous filter, or to a pulp-storage tank if the filter is of the intermittent type. It is this method which I propose to discuss here in a preliminary way, with the idea of going exhaustively into the examination of the results of a series of experiments in a later paper. It may be of interest to note that the design of a cyanide-plant has recently been completed in which the estimated cost of the agitation-tanks, storage-tanks, and pumps was 30 per cent. higher for the charge-agitation arrangement than for the series plan. The first question in studying the series method is, " What is the actual period of treatment undergone by the pulp ?" One first supposes that by chance some of the pulp may get through with little or no treatment, while other portions may stay in the tanks a needlessly long period. The former is not probable or even possible, and the latter is, practically, true

Jan 1, 1910

By AIME AIME

THE year 1940 was an important one in the life of Carl Swartz. At the annual Institute meeting in February of that year, he was inducted into the office of Vice-Chairman of the Institute of Metals Division, and a few months later he assumed another and possibly even more important responsibility-he became the son-in-law of Robert H. Leach, genial vice-president of Handy and Harman, who had just ended his term as Chairman of the Division. The young man who took on this dual obligation in 1940, and who is now commander-in-chief of I.M.D., was born near Danville, Ill., and graduated with honors from the University of Illinois in 1923. (Ed. note: It&apos;s a small world. About the time Carl was a freshman in high school at Danville, or slightly before, the University of Illinois students held beer parties in Danville&apos;s hotel. We know; we were there.) Continuing his education at another of our fine Middle-Western colleges, Carl received his Master&apos;s degree from the University of Wisconsin and his Ph.D. from the same school in 1926. For the next nine years he worked in that splendid training school for non-ferrous metallurgists-the research laboratory of the American Smelting and Refining Co., at Barber, N. J., leaving there in 1935 to take the position of metallurgist of the Cleveland Graphite Bronze Co. in Cleveland, where he is still working (in a modern, air-conditioned office and laboratory) today.

Jan 1, 1942

By Joseph Hodgson

Introduction SINCE about 70 per cent. of the total cost of mining is due to underground work which is out of sight, it is essential that expenditures should be made here to the best advantage. A great many mistakes have been made which were expensive, but perhaps these have not even been detected by mine owners. In the future these may be minimized to some extent, especially if there is cooperative effort on the part of each employee. I have been interested in this subject for some years and have tried to deduce principles and methods. These have proved highly advantageous and may also be of help to others. Some corporations, like the United States Steel, and the Cleveland-Cliffs Iron Co., have done a great deal in this field by having stated meetings of their organizations, with the view to interchanging ideas among their men and educating them along the lines of concerted effort. Since no man knows all about the various branches of mining, it is advisable that frequent meetings of the operating department be held for the interchange of ideas and that all members of the organization have an opportunity to express themselves on the various subjects. It has often been found that in discussions between heads of departments, foremen and bosses, many valuable suggestions may be obtained which promote the best interests of the company. The method regarded as the most conducive to cooperative effort, and pursued by the organization, is to analyze and develope the different phases of various mining subjects at regular meetings.

Jan 5, 1916

By Harry M. Mikami

Refractories are heat-resistant, generally nonmetallic materials used as the linings of furnaces or high temperature vessels in the steel, iron, nonferrous metals, glass, cement, lime, ceramic, chemical, petroleum, paper, and power and heat generation industries. Refractories must have structural strength at high temperatures but also, in many applications, must simultaneously resist chemical-physical corrosion-erosion from stags, metals, granular solids, or gases. Among the major uses are the pyrometallurgical processes for producing iron, steel, copper, aluminum, nickel, lead, zinc, etc. Rotary cement kilns, glass tanks, refineries, utility boilers, chemical and ceramic (including refractories) plants, and a myriad of other smaller scale users employ refractories in the high temperature parts of their operations. Thermal, chemical, and structural conditions under which refractories are used differ widely so there is a great variety of refractories to fill the various needs. Two major classifications are the "basic" and "acid" types. Basic refractories include magnesia and chromite, singly and in combinations, dolomite, and forsterite (olivine). The acid category includes aluminosilicates, alumina, and silica. There are a number of other specialized types such as carbon, graphite, silicon carbide, zircon, and zirconia that have important applications but are used in much smaller amounts than the major categories. Physically, refractories can be divided into bricks and shaped products on the one hand and unshaped or monolithic products (also termed specialties) on the other. There are many further subclassifications and divisions, a discussion of which is beyond the scope of this chapter; see Refs. 2 and 9. Raw materials for the principal basic refractories are magnesia and chrome ore. Magnesia, generally termed magnesite or periclase, is obtained mainly from seawater or saline brines extraction, but substantial amounts are produced from mined magnesite (MgCO3). Dolomite (CaCO3•MgCO3), another important basic refractory, is obtained entirely from mined sources. Acid refractory raw materials are: fire clays, flint clays, kaolin, and other natural clay minerals; aluminosilicate minerals such as kyanite, andalusite, sillimanite, pyrophyllite, bauxitic clays; calcined refractory grade bauxite, alumina from the Bayer process for the alumina group; and quartzitic rocks for silica refractories. The total value of all refractories shipped in the United States in 1974 was $989 million, a record to that date. Of this amount, about 73% represents bricks and shaped products and 27% is in nonshaped or monolithic products which comprise mortars, cements, castables, plastics, and ramming and gunning mixes. Fig. 15.4E.1 shows the rising value of all U.S. refractory shipments in the period 1948-1974. Values of brick and shapes paralleled

Jan 1, 1976

By Carl F. Floe, Hung Liang, Michael B. Bever

DATA on the solubility of hydrogen in iron-silicon alloys are of practical interest, as hydrogen causes gas unsoundness and embrittlement in iron and steel and is also a factor in the metallurgy of cast iron. Zapffe and Sims1 have recently demonstrated that in deoxidized iron and steel castings gassiness and bleeding are primarily functions of the hydrogen content of the liquid metal. These authors also suggested convincingly that ordinary melting and casting practice provides several sources of hydrogen for absorption by the metal. Norbury and Morgan,2 and Boyles3 have shown that dissolved hydrogen affects the graphitization of cast iron. Schneble and Chipman4 included in a study of the effects of superheating on the properties of cast iron an investigation of the part played by hydrogen. Schwartz, Guiler and Barnett6 investigated the significance of hydrogen in the metallurgy of malleable cast iron. A complete interpretation of investigations of this kind calls for equilibrium values of the solubility of hydrogen in the liquid and solid phases. From the theoretical standpoint, the solubility of gases, especially hydrogen, may reveal some aspects of the nature of liquid metallic solutions. This was implied in the early work of Sieverts6 on the effect of alloying additions on the solubility of hydrogen in copper. Recent work by Bever and Floe7 has shown that in liquid copper-tin alloys the solubility of hydrogen changes abruptly at the composition of the intermetallic compound Cu3Sn. It is of considerable interest to determine whether liquid alloys of iron also have compositions at which the solubility of hydrogen exhibits a discontinuous or otherwise unique behavior. Among the various alloys of iron the iron-silicon system is important because of the presence of silicon in various structural alloy steels, transformer sheets, cast irons and special acid-resisting castings. The various grades of ferrosilicon, finally, cover almost the entire remainder of the composition range. Published information on the solubility of hydrogen in iron-silicon alloys is meager. The first values for pure liquid - iron were reported in 1910-1911 by Sieverts and Krumbhaar8 and by Sieverts.9 They found that 100 grams of iron absorbs 28 C.C. of hydrogen at 1550°C. and one atmosphere pressure, and 31 C.C. at 1650°C. In 1938 Sieverts, Zapf and Moritz10 published a value of 26.3 c.c. at 1550°C. Data on the solubility of hydrogen in liquid iron-silicon alloys and in liquid silicon

Jan 1, 1946

By E. P. Whittemore

Experience with the ASC multipoint gas lift system was obtained in Colonia zone of the West Montalvo field near Oxnard, Calif. The wells in this pool produce from depths varying from 10,500 to 12,000 ft. Oil gravity is generally 14 to 15&apos; API with a few extremes of 12 and 20" API. Some salt water is produced which causes some very viscous emulsions. Viscosities at 150F (which is the approximate wellhead temperature) vary from 5,000 to 100,000 SSU. Most of the production is by gas lift, although a few wells are produced by rod and hydraulic pump. About half of the gas-lift wells are on continuous flow and the remainder are on intermittent lift using large, ported, pilot-operated valves for single-point transfer of gas from casing to tubing. Gas-liquid ratios vary from about 6 to 10 Mcf/bbl of gross fluid lifted. Wells are produced to a 450-psi trap system. The following remarks will be confined to intermittent lift only, since this is the type of lift which has been achieved with the ASC valve system. The maximum gross fluid which has been produced by single-point intermittent lift is about 350 B/D in 3-in. tubing and 200 B/D in 21/2-in. tubing with gas-liquid ratios of approximately 7 to 9 Mcf/bbl. Some design changes could reduce this ratio. The ASC multipoint system has provided production as high as 480 BOPD in 21/2-in. tubing with gas-liquid ratios just under 4 Mcf/bbl. To be able to apply the multipoint system, it is recommended that a detailed explanation be obtained concerning transition-point pressure and stabilizer setting—what its significance is to the string design, how it may work for or against the operation of the well, how it is related to tubing sensitivity and how it affects the unloading operation. The unloading operation may only be of academic interest in a technical paper, but to the production foreman, unloading and setting the valves in operation is a very real problem and should be understood in detail. One item touched lightly in the paper was the unloading valve. This valve controls the maximum pressure at which the well can be operated. When lifting heavy viscous fluids, it is most important to set this valve for the maximum possible realistic operating pressure at the surface. If the well lifts easily, it is simple to set the ASC valves at a lower operating pressure and the unloading valve will remain closed; but if the well happens to be heavier to lift than anticipated, it may be desirable to operate on the unloading valve itself and use all the energy obtainable at the bottom of the hole. In the Colonia pool very heavy wet-gas gradients are experienced due to the viscosity of the liquid and the dense mist which is left behind a slug of fluid. There are many combination strings of 3- and 21/2-in. tubing. This aggravates the wet-gas gradient problem and provides wet-gas gradients of about 50 to 70 psi/1,000. An advantage which multipoint lift has provided is increased slug efficiency through better maintenance of pressure under the slug and decreased fall back as the slug passes up the tubing. By using multipoint injection, wet-gas gradients have been reduced to about 30 psi/1,000. This has reduced bottom-hole operating pressure and given a production increase. The ASC valve is not a simple device. It&apos;s operation is difficult to understand, and it must be understood to be used efficiently in gas-lift design. Operating problems are difficult to diagnose—whether they be caused by the fluid lifted, valve malfunction, lift gas rate, or operating pressure. Calculations and reasoning are required to find out what is causing the problem. Inherent in the ASC valve is the inability to create large pressure differentials across a slug. Large differentials may be required to overcome the inertia of very viscous fluid as it is being accelerated in the bottom of the hole. This is tied back to the design of the unloading valve and is one reason for the importance of setting the unloading valve for the highest possible operating pressure. ~u; to the narrow spread the ASC valves provide, it is impossible to cycle slower than about 24 cycles/day on choke control. If small production of 150 BOPD and less is expected, a surface time-cycle controller will be required if the most economical operation is to be achieved. To achieve a satisfactory operation, the operator must keep a record of any changes made in the operating pressure of the ASC valves. Anything which may cause changes in casing pressure in excess of the stabilizer setting will change the valve operating pressure, and if this is not noted from daily inspection of the well casing-tubing pressure recorder charts, the operator will lose control of the well. Significant results can be achieved using ASC valves; however, considerable knowledge is required to design with them, and attention to detail is required for satisfactory field operation.

Jan 1, 1965