Search Documents

By B. T. Brady

Rock mechanics, like all engineering disciplines, must have a theoretical foundation. The subject of this chapter is the formulation of analytical methods that may aid in the rational design and determination of the stability of engineering structures in competent brittle rock materials. By an engineering structure in rock, we mean any (1) excavated sub- surface opening, (2) open surface structure, or (3) system of openings in rock that is virtually self-supporting-that is, not requiring artificial systems to carry structural stresses.

Jan 1, 1970

By W. A. Hockings, M. E. Volin, A. L. Mular

Batch grinding tests at short times were made in a laboratory rod mill with 10 x 14 mesh quartzite in corn syrup-water mixtures of varying viscosity. The weight fraction broken and size modulus were found to be independent of viscosity up to 20 cp, but at higher viscosities breakage of the feed decreased while the size modulus increased. The mechanisms of the effect of viscosity are discussed on the basis of particle dynamics. The effect of viscosity of the suspending medium on grinding has not been accorded much attention, although both wet and dry grinding are used in bene-ficiation processes and the viscosities of water and air differ greatly. schweyerl investigated the rates of grinding of quartzite in a pebble mill with air, water and glycerol as the suspending media and found the rate in terms of new surface developed per thousand revolutions of the mill to be constant and dependent on viscosity up to 20,000 rev, but to decrease and become independent of viscosity for longer grinding times. Based on considerations of the drag forces exerted on suspended particles and on the grinding media under turbulent and laminar flow conditions, viscosity can be expected to inhibit the rate of grinding in a given system as it changes the flow conditions from turbulent to laminar. The objective of this study was to determine the effect of viscosity of the suspending fluid in the batch grinding of a homogeneous feed of uniform size for short residence times, a region of more practical interest than the long times investigated by Schweyer. In actual grinding operations, the viscosity of the fluid does not change, but the consistency (apparent viscosity) of the pulp increases with additions of fines. In this study the consistency of the pulp was not measured because it was thought that the grinding times were too short to alter the apparent viscosity appreciably.* *Minus 200 mesh quartz at 65% solids has an apparent viscosity of about 25 cp as measured by a simple consistometer. Personal communication from D. F. Kelsall to A. L. Mular. For the purposes of this study, the effect of viscosity on grinding can be shown sufficiently well on the basis of the cumulative weight fraction finer than the feed size at any time, and the size modulus, ku, of the finer than feed sizes. The parameter, ku, is obtained from a form of the Gaudin-Schuhmann equation. METHOD AND MATERIAL The grinding tests were accomplished in a laboratory rod mill 10-1/2 in. long and 8 in. bore with a 20-lb rod charge consisting of two 1-in., eight 3/4-in., eight 1/2-in., and eight 1/4-in. diam rods. The mill speed was 43.2 rpm. Charges of 400 g 10 x 14 mesh Wisconsin quartzite** were ground for times of 60, **Courtesy of Minnesota Mining and Mfg. Co. 120, 180 and 240 sec in 500 cc of fluid made up of corn syrup and water in measured proportions. The temperature of the pulp was measured immediately upon completion of grinding, and the size distribution of the quartzite was determined by a wash-wet-dry screening technique. Corn syrup was chosen because of its high viscosity and ideal viscous behavior, and also because its density is not greatly different from that of water. The viscosity of each fluid mixture was measured with an Ostwald viscometer at 25 C. and a correction was made for the temperature of the pulp according to tabulated values for sucrose solutions. The density differences were so small that they probably did not significantly affect breakage. RESULTS AND DISCUSSION The conditions of the grinding tests, computed viscosities, weight fractions finer than the feed size and values of a and ku are listed in Table I. The values of a and ku were taken from the linear portions of the log-log plots of cumulative weight fraction finer vs size for the various grinding times. The plots for tests in fluids of average viscosity 8.6 cp are shown in Fig. 1. In general all of the sets of curves were linear throughout most of the size

Jan 1, 1965

The resin-in-pulp (RIP) ion exchange process was originally conceived by the Atomic Energy Commission in the early 1950's. However it was developed to commercial success by the Anaconda Co. at its 3000-tpd ore processing mill in Grants, N. M. Essentially, the Anaconda mill's crushing, grinding and acid leaching operations are the same as at the nearby Kerr-McGee mill, except that Anaconda uses manganese dioxide instead of sodium chlorate as oxidant during acid leaching. The real differences between the two mills become evident when considering how Anaconda treats its leached materials.

Jan 8, 1974

By AIME

WILLIAM WALLACE MEIN, known to his intimates as "Will" or "Billy", is a mining engineer who has taken the fundamentals of successful mining--operating, engineering, and financial-and applied them to the founding of new industries. Born in Nevada City, Calif., in 1873, Will Mein grew up in an atmosphere of mining, and began to develop his sound judgment in a practical way before starting his formal technical education. As a young man he supplemented his early observations by helping his father, Captain "Tom" Mein, on mining work in California and Alaska. He then went with his father to the Rand, and after a period of milling experience as operator and shift boss he became, in 1894, manager of the chlorination of gold ores at the Robinson mine.

Jan 1, 1947

By Philip Kraft

WHEN it came time to write a biography of Philip Kraft, we got out a copy of Bartlett's "Familiar Quotations" and looked through the references to Travel, Traveled, Traveler, and Traveling, feeling sure there would be some reference to Mr. Kraft. Sure enough, we found: "Travel, in the younger sort, is a part of education; in the elder, a part of experience." Had Francis Bacon done his writing three and a half centuries later, Mr. Kraft might well have served as the inspiration for that sentence. New Yorker born, he received his B.S. and E. M. degrees from Columbia. In 1912, then 22 years old, he took off for Germany where he spent two years studying at the Royal School of Mines, Berlin, for his Doctor of Engineering degree. Contrary to the Greeley-Soule precept, Mr. Kraft, on his return from Europe, went north to South Porcupine. Ont., working as geologist and mining engineer for the Dome Mine. From South Porcupine his next stop was Washington, D. C., where, during the years the country was in the first World War, he was engaged in war work.

Jan 1, 1947

By Arthur A. Center

HIGH GRADE zinc stocks were reported short early in 1943, but not Prime Western. Maximum production of High Grade was expected to be reached before the middle of the year, and demands of new brass mills were to take all of the increase. In February three premiums (A, B, C) of 2 3/4c. per lb. of zinc in ore were announced to encourage production from high-cost mines, the number of premiums being in proportion to estimates of ore-production costs.

Jan 1, 1944

By S. E. Clay

In the chemical reaction control regime employed in the laboratory dissolution experiments, calcined trona ore dissolves in aqueous solutions according to a first order, irreversible reaction rate. The study showed that the reaction is first order with respect to solution NagCO3 concentration. The activation energy was determined to be 20.233 kJ/g. mol with a rate constant equal to 1235 mm/s (2917 in. per min). The dissolving particle may be described by shrinking particle behavior.

Jan 1, 1986

By AIME

AS with Phil Kraft, referred to on this page last month, travel has always held a great fascination for Raymond Frank Baker and for that reason he determined to become a geologist. He had heard that geologists travel and that was what he wanted to do. Now as chief geologist for The Texas Co. his early wish has been fulfilled-he spends almost one third of his time journeying' from one oil field to another. Mr. Baker was born in New Haven, Conn., on Jan. 11, 1892, and went through the public schools in New Britain. A stalwart New Englander, he attended Yale and in 1912 received a degree in civil engineering. For a year following this he worked as a civil engineer for the New York Central Railroad, but his early urge to travel widely could not be satisfied here. So in 1913 he re-entered Yale and until 1916 studied mining and economic geology. He had a little taste of field work, which later became so enjoyable to him, in the summer of 1915 when he worked with the U. S. Geological Survey as a geologic aid. In 1916 he made his first contact with The Texas Co. when he entered their Tulsa office as a geologist. This early career was interrupted by service in the

Jan 1, 1947

By S. J. Page

Introduction Dust from cutter machines and face drills is controlled in most mines by water. However, the large quantities of water used in metal and coal mines for dust control and suppression pose serious operational problems in water soluble ores, such as salt, trona, or gypsum. This paper reviews the strategies to suppress and collect dust on cutter machines and face drills where water usage must be restricted to very low flow rates - typically 3.78 L/min (1 gpm) or less.

Jan 1, 1985

By C. A. Shook, W. H. W. Husband, D. B. Haas

Introduction Although previous studies1,2,3 have been made, no correlations for pressure drop have been proposed. This is probably because severe particle breakage occurred and pressure drops changed substantially with time. A quantitative statement of the relationship of pressure drop to the parameters of the system is desirable for lignite since, unlike higher rank coals, lignite slurries are thixotropic. The present investigation was undertaken to quantify the pipeline behavior and required continuous monitoring of pressure drop and size distribution.

Jan 1, 1980

By A. B. Kinzel

PRECISE knowledge regarding the effect of heat treatment on the properties of steel has made possible the detailed specifications and instructions covering optimum heat-treating temperatures and practices that are in current use. A distinct contrast is presented by the metal-lurgical treatment of steel adjacent to a fusion weld, as such steel is subjected to each, temperature from room temperature to fusion tempera-ture, and cooled at a rate that is not generally controllable but is pre-determined by the nature of the assembly to be welded, the kind of welding used, and the surrounding conditions. This is true regardless of the type of fusion welding: oxyacetylene, electric arc, thermit or flash resistance. Therefore it seemed desirable to investigate the effect of this metallurgical treatment on the characteristics of carbon steels commonly used for welding, by a detailed study of metal subjected to each temperature range; i.e., each heat-affected zone. Oxyacetylene welding was chosen for the investigation because of the experimental facility of accurately segregating and studying each tem-perature zone. The nature of the zones produced by other types of welding is the same. The difference is primarily a matter of dimensions of each of the temperature zones involved. The advantages and dis-advantages of the extent of the zone are of prime moment, and are dis-cussed after the presentation of the detailed zone study. No mention is made of the fused metal proper, as this has been the subject of much published research and the nature of the solidified metal is fairly well known.

Jan 1, 1935

By David R. Mitchell

Many of the difficult operating problems of the preparation of coal for market, of sampling coal shipments and in the utilization of coal are caused by segregation in the coal mass. Segregation may be of two kinds: i.e., "size segregation," in which particles of the same size in a mass of coal containing a range of sizes collect together and "density segregation," in which particles of the same density or specific gravity in a mass of particles of varying density gather together. Mechanics of Segregation Size segregation cannot take place with closely sized coal. As the size range increases, the tendency for size segregation increases. Similarly, cleaned coal with particles of approximately the same specific gravity have very little tendency for density segregation. The wider the density range of particles and the more particles of different density, the greater the chances are for density segregation. The following discussion deals primarily with coal of a wide size range as screenings and of wide density differences as uncleaned or run-of-mine screenings. If a mass of coal containing particles of a wide size range is subject to the stream action of a moving current of water, the small particles are transported farther than the coarser. Particles of different density in a stream of moving water are subject to the laws of classification, the heavier settling out first. The familiar sluice box of the gold miner and the action of rivers and other streams in classifying material according to

Jan 1, 1938

By David R. Mitchell

Many of the difficult operating problems of the preparation of coal for market, of sampling coal shipments and in the utilization of coal are caused by segregation in the coal mass. Segregation may be of two kinds: i.e., "size segregation," in which particles of the same size in a mass of coal containing a range of sizes collect together and "density segregation," in which particles of the same density or specific gravity in a mass of particles of varying density gather together. Mechanics of Segregation Size segregation cannot take place with closely sized coal. As the size range increases, the tendency for size segregation increases. Similarly, cleaned coal with particles of approximately the same specific gravity have very little tendency for density segregation. The wider the density range of particles and the more particles of different density, the greater the chances are for density segregation. The following discussion deals primarily with coal of a wide size range as screenings and of wide density differences as uncleaned or run-of-mine screenings. If a mass of coal containing particles of a wide size range is subject to the stream action of a moving current of water, the small particles are transported farther than the coarser. Particles of different density in a stream of moving water are subject to the laws of classification, the heavier settling out first. The familiar sluice box of the gold miner and the action of rivers and other streams in classifying material according to

Jan 1, 1938

By Albert Sir Kitson

THE manganese ore deposits of the Gold Coast, British West Africa, occur in very ancient rocks, of both sedimentary and metamorphic types. In. certain respects, they strongly resemble those of India and Brazil, as contrasted with those of Tertiary age in Georgia. Viewed from the present condition of the maganiferous rocks, the oldest deposits are in the sediments. Later than these are the progressively metamorphosed representatives of these sediments; youngest are the products of decay and degradation with the concentration of manganese oxide of both areas. The oldest occurrences are in argillaceous and siliceous phyllites and slates, which show only a moderate amount of metamorphism. They belong to a series which also includes mudstones, sandstones, grits, conglomerates and subordinate limestones, with tuffs and lava-flow's largely of basic types. To this series I have given the name Birrim. Its age is unknown, for no definite fossils have been discovered in it. As the characteristics of these non-fossiliferous strata at many places are the same as those of strata in many parts of the world that are suitable for the preservation of fossils and that contain them, it is assumed that the Gold Coast deposits are pre-Cambrian. These rocks of the Birrim series have normally a northeast-southwest strike and are folded, but not to any very great degree except in certain belts. From the Eastern Province of the Gold Coast they may be traversed across their strike for more than 600 miles to the extreme northwestern corner of the Northern Territories. Thence they probably extend much further into French Territory.

Jan 1, 1927

By George S. Rice

The subject of violent bumps in coal mines has been again brought to attention by a recent succession of such occurrences in the coal mines of the Cumberland field of eastern Kentucky and southern Virginia, which have caused fatalities and injuries to underground employees, a report on which is being issued by the United States Bureau of Mines1. The A.I.M.E. has had two valuable papers on bumps in the No. 2 Mine, Springhill, Nova Scotia, each followed by general discussion on bumps and their causes2. This paper gives a brief review of suggested causes and remedial measures given in English, Canadian and United States reports on blimps in coal mines, and then presents suggestions arising from the writer's recent investigation of the bumps in the Cumberland mines, made at the request of the mine operators, to determine the causes and remedies. These bumps, which occur under the simplest natural conditions, provide better opportunity for analysis of causes and effects than afforded under more complex conditions. The simple conditions in this field consist of relatively thin and level coal beds and uniform roof strata free from folding and faulting. Definition of Bumps Bumps in coal mines, as defined in this paper, are sudden violent bursts of coal that usually occur without warning in the extraction of pillars and may or may not be accompanied incidentally by falls of draw slate, upheaval of bottom and smashing of timbers. They are not known to occur where the advancing longwall method of mining, accompanied by

Jan 1, 1936

By George S. Rice

The subject of violent bumps in coal mines has been again brought to attention by a recent succession of such occurrences in the coal mines of the Cumberland field of eastern Kentucky and southern Virginia, which have caused fatalities and injuries to underground employees, a report on which is being issued by the United States Bureau of Mines1. The A.I.M.E. has had two valuable papers on bumps in the No. 2 Mine, Springhill, Nova Scotia, each followed by general discussion on bumps and their causes2. This paper gives a brief review of suggested causes and remedial measures given in English, Canadian and United States reports on blimps in coal mines, and then presents suggestions arising from the writer's recent investigation of the bumps in the Cumberland mines, made at the request of the mine operators, to determine the causes and remedies. These bumps, which occur under the simplest natural conditions, provide better opportunity for analysis of causes and effects than afforded under more complex conditions. The simple conditions in this field consist of relatively thin and level coal beds and uniform roof strata free from folding and faulting. Definition of Bumps Bumps in coal mines, as defined in this paper, are sudden violent bursts of coal that usually occur without warning in the extraction of pillars and may or may not be accompanied incidentally by falls of draw slate, upheaval of bottom and smashing of timbers. They are not known to occur where the advancing longwall method of mining, accompanied by

Jan 1, 1936

By Mark Malamphy

THE occurrence of outcrops of bituminous schists and sandstones impregnated with heavy asphaltic petroleum first directed attention to the Sao Pedro area as a possible source of commercial production of petroleum. Since 1920, more than 20 wells have been drilled in this area. The discovery of oil shows and small quantities of natural gas in some of the early wells led to the continuation of drilling in the hope that more important findings would result. During the early part of 1934, detailed magnetometer observations were made in this area, and a con-siderable number of torsion balance stations were occupied. The results of these geophysical observations help considerably to clarify the structure of the area and the very considerable amount of geologic information available makes possible a much more exact interpretation of geo-physical anomalies. In presenting the results of these observations, and interpretation of the geophysical data, certain actual case problems are included; i.e., geophysical anomalies due to anomalous masses of which the forms and positions are more or less known. Although anomalies due to igneous intrusions are probably more important to geophysicists in Brazil than in other countries, these data have a certain interest for all geophysicists, particularly because they were obtained in the south magnetic hemisphere, where the lines of magnetic force are directed upward, and in a region of moderately low inclination. This is considered as a geological-geophysical problem, and only passing mention will be given to the petroleum possibilities of the area.

Jan 1, 1936

By W. E. Wrather

CURTAILMENT of production was a matter of far more serious concern to the oil industry through 1933 than the search for new supplies of oil. The huge reserves of crude, built up during past years, instead of inspiring a feeling of security, were viewed apprehensively. The status of past laws and court decisions seemed to guarantee to operators the right to produce oil at will, and this entrenched privilege was so widely adhered to that the market was-in a constant state of chaos. The more modern idea of the ownership of oil in place and correlative rights gained headway slowly, since usually there were enough belligerent producers, staunch believers in the old established order, to defeat the efforts of the majority who sought to' introduce order and restraint. State regulatory commissions were unable to cope, with the rebellion among producers with the result that those who abided by proration rulings were penalized, while those who flouted the rulings and produced unrestrainedly were able to make profits on large volumes of flush oil even at low prices. This situation, known in the vernacular as the "hot 'oil" problem, became so acute that the industry was threatened with ruin. The low price for 36c A.P.I. in the Mid-Continent came in April. at 25c per barrel 'but gradually moved upward to the long-hoped for price of $1.00 per barrel in October, after the Federal Government had taken a hand in the matter and effectively allocated production among the oil producing states and materially curbed the "hot oil" runs.

Jan 1, 1934

By L. P. Teas

As sphalerite is such a common constituent of many types of ore, the present investigation was undertaken to determine what its relations are to the other minerals in the deposits, and also whether these are of any genetic significance. The data presented herewith were obtained from a mineralographic study of about 200 ore specimens from some 43 different localities, represented by suites of specimens in the Cornell University collection. These, grouped according to their genesis, were as follows: I. Contact-Metamorphic Deposits.-Silver City, N. M.; Kelly, N. M.; Silver Bell, Ariz.; Bingham, Utah; Agaguca, Michoacan, Mex.; Matehuala, Mex.; Sombreretti mine, Mex. II. Deep-Vein Zone Deposits.-Mineral, Louisa Co., Va.; Edwards, N. Y.; Chestnut Yard, Va.; Allah Cooper mine, Louisa Co., Va.; Globe, Ariz.; Moyie, B. C.; Rossland, B. C.; Broken Hill, N.S.W.; Weedon, Que.1 III. Intermediate-Vein Zone.-Park City, Utah; Leadville, Colo.; Butte, Mont.; Santa Barbara, Mex.; Red Cliff, Colo.; Burro Mountains, N. M.; Idaho Springs, Colo.; Blue River, Ore.; Rye, Colo.;1 Slocan district, B. C.; Freiberg, Ger.; Clausthal, Ger: IV. Shallow-Vein Zone.-Ouray, Colo.; Goldfield, Nev., Zacatecas, Mex.; Field, B. C.; Kapnik, Austria; Frontenac mine, Kingston, Ont. V. Meteoric Water Deposits.-Joplin, Mo.; Southwest, Wis.; Austinville, Va.; Crittenden County, Ky.; Ridgeburg, Pa.; Moresnet, Belgium. It is not supposed that the investigation of such a limited number of occurrences may warrant conclusive and universal generalizations, but the conclusions reached are believed to be reliable in so far as the specimens, that were examined are concerned.

Jan 11, 1917

By John P. Cosgro

THE increasing use of internal furnace-boilers for mining power-plants (doubtless due to the facility with which they may be installed by reason of their portability; the fact that they require no masonry setting, cast-iron fronts, buck-stays, etc., and practically no foundation; and the successful maintenance of their claim to equal and even superior economy, as compared with boilers of other types) warrants this description of a method of remedying an injury which may occur, to such a furnace, even though it satisfies the requirements of the formula adopted by the U. S. Board of Supervising Inspectors of Steam Vessels.2 I refer to the sagging and deformation which may result from overloading the boilers for a considerable period-say, several days. This is sometimes unavoidable under the exacting conditions of continuous day-and-night service, and (in spite of all rules and precautions, the occasional careless or unskillful work of attendants. Such a trouble is by no means unknown on shipboard, where this type of boiler is so largely employed. In the case here described, two Morrison suspension-furnaces, of half-inch steel, 14 ft. long and 45 in. in mean diameter, with ? dry-back ? boilers, were necessarily operated somewhat beyond their rated -normal capacity for several months, while a third similar unit was -in process of installation, and during this period, though the boilers were kept perfectly clean, heat seems 'to have been generated slightly faster than it was absorbed by, the water in the boilers. The corrugations of this.

Mar 1, 1905