Search Documents

By A. P. Pipilen, M. Weintraub, W. F. Hosford, A. A. 230-000-000-006 Orning

In a study of the principal factors affecting the transport of coal-water mixtures through a centrifugal pump and a pipeline, the interrelation between solids concentration, velocity, and pressure drop was established for a minus 2-in. bituminous lump coal in concentrations up to 48% by weight. Optimum concentrations were found to exist for maximum capacity of a given pipeline and for minimum energy requirements per ton of coal. Coal size degradation by particle fracture took place in the pump; abrasion and attrition to form fines took place in both pump and line. A novel system of studying flow of solid-liquid mixtures in pipelines by the determination of relative sound intensities was developed. The hydraulic transport of minerals is in part an established art and in part a relatively new field of industrial technology. The established art developed especially where the mineral was under water, where water was used in hydraulic mining, or where large quantities of water had to be pumped from the mining site to expose the mineral. Power requirements and limited life of pumps and pipelines, under such conditions, were relatively unimportant. Examples may be found in dredging, and in hydraulic mining and transportation of phosphate rock.' In the design of a coal pipeline the most needed information relates to flow characteristics, power requirements, pressure drop, size degradation, and size segregation as a function of solids-water ratio and size distribution of the mineral. A considerable amount of information has become available concerning pressure drop and energy requirements.2'3 These topics were therefore not studied intensively. Coal degradation, however, has not been clearly delineated. Lammers and coworkers4 showed that coal may be severely degraded in size but did not distinguish between degradation produced in the pump and in the line. It is the primary purpose of this paper to outline techniques used to acquire some of the much needed design data. A full report of the investigation is to be published by the Bureau of Mines at a later date. APPARATUS AND PROCEDURE The apparatus for circulation tests (hereafter referred to as Type III tests) consisted essentially of a loop and a centrifugal solids handling pump, with attendant instrumentation, and coal weighing and feeding equipment. It also included an adequate water supply, as shown in Fig. 1. The selection of 6-in., schedule 40, carbon steel pipe was based on the top size of coal to be used. Assuming that the top size of coal should not exceed 1/3 the inside diameter of the pipe, a 6-in. pipe would accommodate 2-in. coal, a realistic size for transport from the mine face. An 872-ft loop was constructed first. Later a few tests were made with a lengthened circuit of 1361 ft by superimposing an additional loop on the original one. All bends used were of 3-ft radius. A noisemeter microphone, taped to the pipe at various points, but generally about 50 ft downstream of the pump, was used to sense segregation of the coal and the length of slugs of coal in water. To measure the stream velocity, radioactive sources were encapsulated in plastic cubes. The specific gravity of the blocks was adjusted to 1.3 and 1.8 to simulate low ash and high ash coal particles. Their passage through the pipeline was detected by a Geiger counter. Because the repeated circuits of the Type III tests did not permit coal degradation in the line to be distinguished from that produced by the pump, the two

Jan 1, 1964

By T. E. Leontis

ONLY a limited amount of information has been published on the effect of thorium as an alloying ingredient in magnesium. McDonald13'2 showed that the addition of thorium in amounts up to 3 pct increases significantly both the ductility and the strength of rolled magnesium sheet. A recent publication by Sauerwald" indicates that thorium contributes strength and creep resistance at elevated temperatures to magnesium in both the cast and wrought states. The observations of Sauerwald are confirmed in this paper, which presents the results of a systematic study of the effects of compositional variation on the tensile properties, creep resistance, conductivity, density, and metallography of Mg-Th alloys containing up to 50 pct Th both in the sand-cast and in the extruded states. The effect of the addition of cerium to Mg-Th alloys is also reported. Experimental Methods The alloys studied in this investigation were pre.pared in small laboratory melts according to the melting practice described by Nelson4 as the crucible method. Electrolytic magnesium was used as the starting material to which the thorium* was introduced in metallic form. It was observed that the behavior of thorium in molten magnesium with respect to reaction with protective fluxes is similar to that of rare-earth metals. In order to obtain the highest possible alloying efficiency, it is necessary to use non-MgC1, fluxes and to apply all the precautions described by Marande6 for melting, alloying, and casting magnesium-rare-earth alloys. .Under these conditions it is possible to obtain an alloying efficiency in the range of 85 to 95 pct. The Mg-Th-Ce alloys were made with cerium of the highest purity available, not with the commercial product "misch-metal" which contains approximately 50 pct Ce. The total rare-earth content of this material was 97.1 pct, of which 0.3 pct was rare-earth metals other than cerium; the major impurities comprising the balance were iron and magnesium. The thorium and cerium contents of each alloy were determined chemically. Test bars 6% in. long with a 2% in. long reduced section of % in. diam were cast in sand molds using a four-baf pattern. In most cases, a 3 in. diam extrusion billet 10 in. long was cast in a steel mold from the same melt used for making the sand-cast test bars. For the higher thorium alloys, it was necessary to remelt the foundry scrap from the test bars in order to make the extrusion billets. The billets were scalped to a diameter of 2 15/16 in. and the ends faced to a length of 9% in. as limited by the size of the extrusion container. The alloys were extruded into % in. diam rod on a 500-ton direct-extrusion press. The details of the extrusion process are as follows: Billet preheat 925°F (2 to 16 hr) Container temperature 900 °F Die temperature 900°F Extrusion speed 10 ft per min Reduction ratio 36:1 Percent reduction 97.3 Alloys containing up to 10.2 pct Th were preheated at 925°F for 2 hr; all alloys with higher thorium contents were preheated for 16 hr. In order to establish the effect of extrusion temperature, billets of

Jan 1, 1953

By I. Fatt

The chromalographic effect refers to the separation of constituents in a moving fluid phase which occurs when the phase is passed over a stationary phase, either solid or liquid, or large areal extent. In performing chemical analyses, the large surface contact areal is provided in the case of gas-solid chromatography by-passing the gas over a porous solid and for gas-liquid chronla tog rap hy by-passing the gas over a porous solid which has been coated with a nonvolatile liquid. The porous medium is usually placed in a cylindrical tube, although it may be a relatively flat sheet as in paper chroma-tography. According to one theory,' the separation results from the difference in time spent by various components in the stationary phahe. A gaseous component which is conlpletely insoluble in the stationary phase, or is not adsorbed on the solid, proceeds unimpeded through the column. The versatility and power of the various types of chromatogruphy for the analysis of complex mixtures are evident from their widespread use in performing chemical analyses and from the large number of symposia, books, and papers devoted to the subject in recent years. Associated developments are the application of chromatography to the determination of heats of solution, heats of adsorption, solubilities orK-values, etc. Gas-liquicl chromatography analyses may be characterized by the manner in which the samples are introduced and displaced from the column'. The three techniques used are known as (1) frontal analysis, (3) displacement analysis, and (3) elution analysis. The frontal analysis is performed by displacing an inert gas from the column by a continuous stream of the sample. As indicated in Fig. l(A), all but the first fraction leaving the column represent mixtures rather than pure components. The displacement analysis is conducted by filling the column with a sample, then displacing it with a more strongly adsorbed or absorbed vapor. The resulting chro-matogram is illustrated by Fig. 1(B). Finally, in the elution analysis a small sample of the mixture to be analyzed is introduced as a "plug" into a Rowing stream of carrier gas to give an elution-type chromato-gram. Fig. l(C). The three techniques may be used to provide models to which Row patterns in other physical situations may be compared. PURPOSE OF THE INVESTIGATION The purpose of this investigation was to determine whether natural reservoir rocks, when coated with crude oil, provided sufficient surface areas to give rise to a chromato-graphic separation of light hydrocarbon constituents. The tests were conducted with the light hydrocar-bons in the gaseous state. SANDS TESTED Two sands of widely different permeabilities have been studied: (1) Ventura core (16 md), and (2) Torpedo sandstone core (578 md).Table 1 gives a description of the cores that were tested. With the exception of one frontal-type flow arrangement which was performed on Core 3, the tests were of theelution-type in which a methane-propane mixture was eluted through the core by means of helium. The Ventura core, when impregnated with a weathered crude from the same field, became so impermeable to gas flow that it was necessary to conduct the tests on the granulated cores (Cores 2 and 3).

By K. E. Nelson

The effect of thorium and zinc variations on the strength and 100-hr creep characteristics of Mg-Th-Zn-Zr alloys was investigated. Optimum resistance to creep at 650° and 700°F are attainable within a certain range of thorium and zinc contents. This range does not conform to that which develops maximum tensile properties. RAPID advances have been made during the last few years in the development of magnesium alloys for elevated temperature applications demanding high resistance to creep. The beneficial effect of rare-earth metals on the creep resistance of magnesium alloys has been emphasized by a number of publications1-13 and such alloys are now in commercial production. The use of thorium as an alloying ingredient in magnesium was mentioned by McDonald and also in two Alien Property Custodian patent applications.10,17 The initial observation of Sauerwald that thorium contributes still higher creep resistance to magnesium than is attainable with rare-earth metals has recently been substantiated.'" " In fact, it has been demonstrated that the useful temperature range of magnesium alloys is appreciably extended by the use of thorium. In all cases, it was observed that zirconium must be included in the alloys in order to render them fine grained and more readily castable. Several recent publications:2-27 indicate that a still further improvement in creep resistance and a further extension of the useful temperature range can be realized by the addition of zinc to alloys. The primary purpose of this paper is to present the results of a comprehensive study of the effect of zinc on the strength and creep characteristics of Mg-Th-Zr alloys. Compositions covering the range of thorium content from M to 6 pct and zinc content from 0 to 5 pct have been investigated. The creep characteristics at 650" and 700°F reported in this paper are based on results of tests of 100-hr duration. It is appreciated that creep tests of 100-hr duration might not yield adequate data for design purposes for parts with much longer expected life. However, for the purposes of the present discussion, it is felt that the combination of stresses and temperatures used in the 100-hr creep tests have yielded a clear representation of the compositional variation of creep resistance at the temperatures investigated. Creep tests of 1000-hr duration are now in progress on a few of the most promising alloys. Preparation and Testing of Alloys The alloys studied in this intensive investigation were prepared in 25 lb capacity mild steel crucibles. The thorium, zinc, and zirconium were alloyed and poured as described in earlier publications The thorium was introduced into the melt in the form of a Mg-Th hardener," the zinc added in the metallic form, and the zirconium alloyed in the form of the commercial hardener containing magnesium and 30 to 50 pct Zr.10, 26 Fluxing practices for melting and refining were the same as for magnesium-rare-earth metal-zirconium alloys. The melts were sampled for analytical determinations and poured into separately cast 1/2 in. diameter standard tensile bars. The test bars were given a precipitation treatment of 16 hr at 600°F in laboratory furnaces. It has been shown by other tests that a high temperature solution treatment followed by an aging treatment is unnecessary for the development of optimum properties in Mg-Th-Zn-Zr alloys. The selection of 600°F as the aging temperature was based on an attempt to achieve metallurgical stability without coalescence of the undissolved phases and the attendant loss in strength. The thorium, zinc, and zirconium contents of each melt were determined chemically. The zirconium contents are reported in two parts, "soluble" and "insoluble," referring, respectively, to the portions present in the alloy which are soluble and insoluble in dilute HCl acid. Distinction is being made between these two components of the zirconium content in the alloys because it has been found that only that portion of the zirconium content which is soluble in dilute inorganic acids affects the structure and properties of the alloys. The usual impurities consisting of copper, iron, manganese, and nickel were determined spectroscopically. The analysis for each melt is listed in Table I. A description of the methods of tension and creep testing has been detailed in earlier papers. The tests were performed with the cast skin re-

Jan 1, 1954

By P. D. Southgate

VIBRATION, both ultrasonic and sonic, can affect the course of a variety of metallurgical processes. Reports of work on this subject have appeared at intervals over the last twenty years and a thorough review has been made by Hiedemann,' who gives a full list of references. It has been established that both refinement of structure and outgassing of the melt can be produced in most metals with sufficiently intense vibration. Many of the experiments in this field have been carried out using alloys of direct commercial interest in production- type casting equipment. Here a different approach is adopted, and simple binary alloys which exhibit different types of structure are used to facilitate examination of the effects produced under well-controlled conditions. Results from this kind of experiment should enable the basis of larger scale experiments with similar types of materials to be better substantiated. The alloys selected for this work are: 1) aluminum of 99.2 pct purity, the principal impurity being iron, near 0.4 pct; 2) A1-1.8 pct Fe, which is near eutectic composition; 3) A1-4 pct Fe—the second phase, of composition FeAl3, forms distinct acicular crystals; and 4) A1-12 pct Si—although this is of eutectic composition, the silicon normally appears in the form of large plates. Experimental Method There are three practicable methods by which acoustic vibration can be transferred to liquid metals: a) vibration of the whole of the container; b) electromagnetic induction; and c) insertion of a vibrating probe into the liquid. Method c is chosen here, and a frequency of 8 kc per sec is used. The end of the probe is electrically heated so that the metal near it will be the last to solidify. This ensures that vibration is transmitted directly to the liquid metal without passing through any solidifying and pasty intermediate region, which would attenuate acoustic waves severely. In addition, the heating prevents solid metal adhering to the probe, with consequent detuning. The transducer assembly is shown in Fig. 1. A stack of Permendur laminations 30 cm long acts as a half-wave vibrator and a winding along its length carries polarizing and energizing currents. It is joined by a half-wave coupling bar to a mild steel exponential horn, which tapers from 3.8 to 1.1 cm diam. A stainless steel stub 3 cm in length is welded on the free end. The assembly is supported by a plate located at the node of the coupling bar. Acoustic radiation losses are minimized by allowing the free end of the transducer to protrude above the surface of the cooling water. The exponential horn serves the function of matching the acoustic output impedance of the transducer to the radiation resistance of the probe into the melt. Electrical drive is provided by a 1 kw generator. Measurements of probe vibration amplitude during melt treatment are obtained from a gramophone pick-up with the needle attached to the wide end of the horn. This device is calibrated with a microscope before use. Liquid aluminum is very actively erosive and solution of materials with which the molten metal comes into contactcauses difficulties. Erosion of the probes in particular can be severe since it is greatly accelerated by the vibration. Tests of various acous-

Jan 1, 1958

By H. W. Bell

There was considerable prospecting for new supplies of oil in Arkansas during the past year, regardless of the overproduction affecting the industry throughout the country. Justification for this new work was not lacking, as the local markets more than threatened to absorb a declining production. There were, however, no important new discoveries in the state during 1929. The McDonald area in sec. 2515, S.-18 W., threatened to expand into a major producing area. Oil showings had been encountered here in wells drilled by the McDonald Oil Corpn. as early as the fall of 1928. In July, 1929, an initial production of 1000 bbl. of 32" oil was obtained in McDonald Bros. B-3 Wilson, from a sand at 2780 to 2786 ft., which is about 80 ft. higher than the sand previously tested in the neighboring wells. This production declined rapidly. At the end of the year there were six producers making about 200 bbl. per day total. Seven dry holes have temporarily stopped development in that area. The showing of B-3 was sufficient to cause considerable leasing activity. The area lies several miles west of the Louann portion of the Smackover field. The discovery well went to 2873 ft. and found Glen Rose lime in bottom. The age of the producing sand is in doubt; it seems closely related to the Tokio sand. During 1929, several paying wells were brought in, as a northeastern extension to the Smackover Heavy area, in sec. 34 and 35-15-15, from the Nacatoch sand. Over 20 new wells were drilled and resulted in at least 1500 bbl. production. The down-dip or off-structure territory contiguous to the Smackover uplift was further tested at various locations with the usual results; that is, a showing of "salt water gas," which soon blew off and in some cases a slight showing of oil. These gas showings, found further down the dip than oil, are the results of the ability of water to take gas into solution at the rate of about 3 per cent. by volume at atmospheric pressure and proportionally larger quantities, if available, at higher pressures (measured on the absolute scale). During the year no off-structure wrinkles sufficient to trap conlmercial quantities of oil have been found outside of the other known fields of

Jan 1, 1930

By FRANK COLE

THE territory covered in this discussion includes all the states west of the Mississippi river. Agriculture is expanding each year in this section, but until recent years the application of commercial fertilizers as an aid to crop production was not practised to any great extent. The use of commercial fertilizers has increased somewhat, but is still on a small basis as compared with the tonnages used else- where in the United States. During 1928 these western states used 665,100 tons of all classes of fertilizer as compared 'with 7,933,600 tons used in the whole United States; or this western area, compromising near- ly two-thirds the land area, uses about 5 per cent of the total fertilizer. To show how large a tonnage one state may consume, North Carolina for the year 192s used 1,349,360 tons of commercial fertilizer or about twice the amount used by 22 western states.

Jan 1, 1930

By Charles S. Barrett, Frederick N. Rhines, Robert F. Mehl

The solid solutions which aluminum forms with copper, and with magnesium and silicon, are not extensive, and accordingly could not be expected to form Widmanstatten figures profusely nor with great ease. A study of the Widmanstatten figures in these systems seemed desirable, however, because of the interest which these alloys bear towards age-hardening theories resulting from the necessary relationship between the age-hardening phenomena and the atomic processes leading to the formation of Widmanstatten figures.' Alloys of Aluminum with Copper The most accurate determination of the solid solubi1it.y of copper in aluminum seems to be that by Dix and Richardsoq2 whose results are represented in Fig. 1. According to this work, aluminum dissolves 5.6 weight per cent of copper at 548", and less than one per cent at room temperature. Judging from the constitutional diagram, this solid solu-lion on cooling tends to precipitate the compound CuA12, and this conclusion has been confirmed experimentally by Schmid and Wassermann.

Jan 1, 1932

By B. A. Rogers

ACCORDING to petrographic investigations, 1-4 cooled steel furnace slags contain a number of substances that have been shown to be ferro-magnetic5,6 and hence capable of undergoing appreciable changes of susceptibility with temperature. Since any alteration of the suscepti-bility of a constituent affects the average susceptibility of the sample, information concerning the nature of the substance should be deducible from its magnetic behavior. The possibility of obtaining information concerning slags in this way led to the construction of the apparatus to be described. FUNDAMENTAL PRINCIPLES OF APPARATUS The most convenient method of observing changes in mass suscepti-bility? with temperature is the one employed by Curie7 in his original investigation of the changes in magnetic properties of substances at elevated temperatures. As the method has been described frequently in the literature and in textbooks, only a brief review of the fundamental principles need be given here, but the particular arrangements used in the present work require a more detailed description.

Jan 1, 1939

By L. M. Cathles, H. R. Spedden, E. E. Malouf

Fluid flow through an igneous rock formation will occur mainly through fractures. A non-diffusing or slowly diffusing tracer (such as .5µ silica spheres identifiable under electron microscope) will arrive at a monitor well when enough fluid has been injected to displace the volume of water in the flow fractures between the injection and monitor wells. A rapidly diffusing tracer (such as NaC1)-will diffuse into the matrix blocks and so a volume of tracer nearly equal to the total fluid volume contained in the rock formation between injection and monitor wells must be injected before significant diffusing tracer arrival will be noted. The flow fracture porosity is typically one hundred times smaller than the total porosity of an igneous formation. The shift between diffusing and non diffusing tracer arrivals, together with the diffusional characteristics of the tracers, can define the diffusional accessibility of the matrix blocks of an igneous formation. A field test of these concepts and the problems encountered will be described.

Jan 1, 1974

By Frank A. Wardlaw

My subject covers the effect that recent metallurgy has had on operations at the Utah-Delaware mine. This mine is the old Highland Boy mine of Bingham Canyon, Utah, one that has now been in operation for about 30 years. It was first operated by Messrs. Weir and Newhouse as a gold mine, under direction of the Highland Boy Gold Mining Co. The ore was oxidized gold ore and it was treated on the property in a cyanida-tion plant. During the process of development, sulfide ore was found assaying about 5 per cent. copper. It proved to be the discovery of what is yet the largest sulfide copper orebody in the State. The first shipment was made in December, 1896. A smelter was built in Salt Lake Valley to treat this ore and not long after the property was sold to the Utah Consolidated Mining Co. From 1900 to 1924, the mine was a large producer of direct-smelting ore which averaged for many years 4.5 per cent. copper, then later dropped to 2 per cent. copper. During the years 1912 to 1920, direet-smelting lead ore was also mined. In 1918 and 1919 ore developments at depth showed a decided increase in silica content and a porphyry sill so closely associated with the ore that it was impossible to mine the ore clean and it was found necessary to build a copper flotation concentrator at Tooele. The mill had a capacity of 1000 tons a day and made a recovery of 90 per cent., and would have been responsible for a continuance of profitable operations had it not been for a slump in the copper market and the necessary high cost of mining ore on the lower levels. Results of Selective Flotation In 1924 the mine was on the point of a shutadown which had all the earmarks of being permanent; it was being operated at a heavy loss and preparations were made to pull the pumps and salvage the machinery. The plant at Tooele was remodelled for selective flotation by the International Smelting Co. in order to treat custom ores, and incidentally to clean up a possible 10,000 tons of lead-zinc ore which it was thought possible to get in the Utah-Delaware before shutting the mine down. Results were so encouraging that an effort was made to develop more lead-

Jan 1, 1928

By W. A. Wall, R. L. Kidd

IN present-day flotation practice, grinding of the flotation feed is carried to extremely fine sizes, 70 to 80 per cent minus 200 mesh being customary. The greatest flotation losses occur in the coarsest and finest sizes, but the losses in the very fine sizes are, of course, much the more important because of the large proportion of fines in the feed. These losses are particularly high in zinc ores so a study of the effect of size on the flotation of sphalerite has been made. The mineral used in these experi¬ments was a pure sphalerite, especially free from copper, from the Joplin district in Missouri. The sizes coarser than 200 mesh were separated by screening, the sized mineral then being deslimed on a Wilfley table. The sizes finer than 200 mesh were obtained by water elutriation as described by H. R. Bradford (M. S. Thesis, University of Utah, 1932) ; particles finer than 6.5 microns could not be obtained with the apparatus used.

Jan 1, 1933

By Dean W. Lynch

Arizona: The San Xavier Indian Reservation mine is located approximately 2 ½ miles northwest of Asarco's Mission Mine southwest of Tucson. The company plans to produce oxide and copper-bearing siliceous ore at this operation, construction of which is scheduled for completion in 12 months. Asarco also plans a copper leaching and iron precipitation plant at its mine. The plant will leach 4000 tpd of oxide ore using sulfuric acid produced at the company's acid plant now under construction at Hayden. Copper precipitates will go to the smelter at Hayden. A drilling program at the Sacaton copper prospect in Pinal County, has disclosed two porphyry copper deposits. One deposit, mineable by surface mining, has approximately 17 million tons of material averaging 0.80% Cu. A deeper deposit suitable for under- ground mining has approximately 12 million tons averaging 1.5% Cu. Although Asarco intends to place this property in production, no startup date has been determined.

Jan 1, 1970

The Library belonging to the Institute is now administered as part of that of the United Engineering Society, the members of the Library Committee representing the Institute on the Library Board of the United Engineering Society. The main collection now consists of 115,900 books, 3680 pamphlets, 5811 maps, and 4402 searches, making a total of 129,793, a net gain of 7701 within the year. There is in addition a lending collection of 1004 volumes and one of duplicates amounting to 11,310. The library grows steadily both by gift and purchase. The cataloging is now substantially current covering 124,100 items represented by 362,145 cards. There are many rare and notable books, especially those relating to early engineering. It is truly a great treasure house of knowledge. While no severe effort is made to record all visitors the books showed 23,470 to have used the Library in 1928. In addition 5102 telephone requests for information were answered, 202 searches and 196 translations made and 34,964 photo prints furnished. The service department is maintained by small fees which cover the cost. The total amount appropriated for operating expense for the year was $46,300, of which $8,240.02 was furnished by the Institute, $5,399.45 being derived as income from the Douglas Library Fund and the remainder from current receipts. Within the year a slight change was made in the method of meeting the expenses of the Library, a flat charge of $5,000 per year being made against each of the four Founder Societies and this being supplemented by a surcharge based upon membership. The effect of this has been for the present to decrease slightly the amount that the Institute would otherwise need to pay. Placing in one collection all the books of the four societies greatly increases the number of books accessible to the members of each and opening the Library to the public is an important factor in keeping the tax exemption privilege enjoyed for the building. The Director and Staff of the Library make every effort not only to accommodate those who come in person to consult the collection but members resident elsewhere who communicate by letter or wire. The facilities of the Library are truly available to all.

Jan 1, 1929

C. G. Dunn (Generai! Electric Research Laboratory)— The author is to be commended on his attempt to calculate the residual strain energy from information on the dislocation density within the subgrains and a surface energy associated with the subgrains. However, much closer agreement between a calculated critical size of a nucleus and the observed size of grains that did not continue growing can be obtained if a reasonable correction is made in obtaining the energy of the surfaces of the subgrains. For example, since the sample is a single crystal with a cold-rolling reduction of 70 pct in thickness, one needs either an average disorientation for this or an average subgrain boundary energy rather than the 2.5 deg disorientation of a bent crystal, which was used by the author. From either the Laue photographs of the author or the pole density plot of Koh and Dunn 16 for a (113) [332] cold-rolled crystal the

Jan 1, 1961

By Parke A. Hodges

CHROMIUM, one of the most vital of the strategic metals, has constantly increasing importance as research expands potential uses in alloy steel metallurgy. All signs point to a steadily growing use for chrome ore, and the general subject has received a great deal of attention recently.1 A relatively little known country, Southern Rhodesia produced a total of 5.949 million tons, or 18.6 pct of the total world chrome output, between 1906 and 1950, according to figures from the U. S. Dept. of Commerce. According to U. S. Bureau of Mines figures, Southern Rhodesia produced 291,525 tons in 1950 and 300,267 tons in 1951, or approximately 13 and 11 pct, respectively, of world production for the two years. In 1953 the Rhodesian Vanadium Corp. produced about 85,000 tons of which probably 7,000 tons were concentrate. Production by other companies was high. Large in themselves, the figures assume even greater significance because most of this output is of metallurgical grade.

Jan 8, 1954

By Toshio Kurikami, Charles A. Brockmiller, John E. FitzSimmons

In the manufacture of sulfuric acid from SO2 bearing gases, the presence of mercury vapor in the gases may lead to unacceptably high mercury levels in product acid. Anticipating inception of regulations requiring low mercury acid, St. Joe Minerals Corporation and Toho Zinc Company, Ltd. independently developed new mercury removal technology. The processes may be used individually or in combination, depending upon the mercury content of the SO2 gases and the required mercury level in acid, for efficient control of maximum mercury levels in sulfuric acid. The St. Joe B Process removes mercury from roaster off-gas streams, while Toho’s NAK Process precipitates Hg from concentrated sulfuric acid. The combined process is commercially operated at St. Joe's zinc smelter in Monaca, Pennsylvania, and the NAK Process at Toho’s Chigirishima lead smelter and Onahama zinc roasting plant in Japan. Product acid mercury levels of 0.5 mg/kg are economically achieved.

Jan 1, 1976

By M. E. Steidlitz

FABRICATION of semiconductor devices.requires the formation of electrical contacts, often involving the use of lead, tin, and lead-tin solders. In several recent instances when germanium had been bonded to nickel with lead, a new metallic phase appeared, unattached to either germanium or nickel, but rather suspended as a continuous foil wholly contained within the lead matrix. Since such metallic structures do not form in nickel-lead or lead-germanium systems under identical conditions, a brief study was made of the characteristics and possible formation mechanisms of this material. EXPERIMENTAL Specimens were prepared by placing single crystal, transistor-grade germanium discs, 30-mils in diam by 6-mils thick, into a depression in a graphite boat. =A* nickel washers, 125 mils in diam by 5-mils thick, containing a center hole of 10-mils diam, and coined into a soup bowl shape, were loaded on top of the discs, so that the bottom of the

Jan 1, 1959

By N. A. DeCecco, H. M. Meyer

IN the early stages of a titanium brazing investigation, binary titanium systems partially or completely known and fundamental metallurgical data were surveyed to select the pure metal most likely to be satisfactory for producing a ductile high strength joint. The phase diagrams for the purpose of this survey were classified into two groups: 1—systems with large solubility in ß titanium, but negligible solubility in a titanium, and 2—systems with large solubility in a titanium. Those metals with melting points believed to be too high or too low for titanium brazing (Tim = 1730°C) were eliminated from consideration. The melting points of vanadium, tungsten, tantalum, hafnium, zirconium, and the platinum group are too high and those of zinc, lead, cadmium, and tin are too low. The remaining metals were grouped as follows: 1—large ß solubility: Cr,¹ Mn,² Fe;³ CO,4 Ni,5 Cu,6 Be,' Si." —large a solubility: Al.9

Jan 1, 1954

By Henry Mulryan

THE largest and purest known deposit of diatomite is being actively mined and processed 3 ½ miles south of Lompoc, Santa Barbara County, Calif., by the Johns-Manville Products Corporation. The workings FIG. 1-LOCATION OF DIATOMITE DEPOSIT AT LOMPOC. cover 4000 acres, the depth of economically recoverable diatomite being 1000 ft. (Fig. 1). Lompoc, a community of 2500 population, is situated in the Santa Ynez River Valley 10 miles inland from the Pacific Ocean. It is 44 miles

Jan 1, 1936