Search Documents

By Colin Baker, G. C. Smith

Investigation of the initiation and propagation of ductile failure in OFHC copper was undertaken to determine the role of nonmetallic inclusions. The effect of inclusion initiated voids on the formation of the internal cavity and the final shear separation was studied by metallographic eranzination of strained test pieces. A strain anneal technique was used to enlarge the voids under uniaxial stress conditions to elinzinate triaxial stress effects. Measurements of void size us stress and strain were made to show the point at which void im'tiation begins and becomes an important factor in the deformation process. The work of separation of copper-cuprous oxide was determined to attempt to correlate the breakdown of the matrix inclusion interface with void initiation and propagation. The zloid shape and position relative to the tensile axis suggested an interface breakdown mechanisnz of initiation. Evidence is presented that shows a basic similarity between the central cavity propagation and the 45-deg shear portions of the failure. DUCTILE fracture has been studied by a number of workers1-lo and attention drawn to the importance of hard second phase particles in the initiation of the failure. Holes formed at the matrix-particle interface can elongate by plastic deformation and then subsequently expand sideways to link up and produce a major crack. This is usually observed first in the center of the macroscopically necked region of a test-piece where the hydrostatic stresses are at a maximum. As the crack spreads sideways towards the free surface of the specimen, well defined shear zones develop from the crack tip and the final separation is along a direction at approximately 45 deg to the stress axis. This shear failure may also be associated with voids formed adjacent to second phase particles. In this way a cup and cone type fracture is produced. The stage at which separation takes place between particles and the surrounding matrix has not been clearly identified. In addition, although researchers have dealt with anisotropy of tensile behavior" as a result of material fabrication variables, not much is known about the microstructural features of aniso-tropic behavior. In the present work evidence on these points is presented in relation to the behavior of copper containing second phase particles of cuprous oxide. I. MATERIALS AND PROCEDURES EMPLOYED The material used was +-in. diam or 2-in. sq cold-drawn OFHC copper bar which contained 0.6 pct by volume of cuprous oxide inclusions. These ranged in COLIN BAKER, Junior Member AIME, formerly at -mnF of Metallurgy, University of Cambridge, Cambridge, England, is presently Research Scientist Reynolds Metals Co., Richrnand, Va. G. C. SMITH, Member AIME, is Senior Lecturer, Department of Metallurgy, University of Cambridge. Manuscript submitted June 20, 1967. IMD size from approximately 1 to 6 p in length and 1 to 4 p in width. The shape was generally slightly ovoid. Tensile tests were made on specimens having a gage length of 2.5 cm and diameter of 0.643 cm. Metallographic examination was carried out by sectioning deformed and fractured specimens; in addition fracture surfaces were examined optically and with a scanning electron microscope. Some measurements of the work of separation between copper and cuprous oxide were made, using a sessile drop technique which was a modification of that used by Kingery and umenick." The best metallographic results were obtained by using a vibratory polisher, which minimized smearing of the surface. 11. RESULTS A) Initial Experiments. Specimens from the +-in. diam rod were annealed for 2 hr at 650°C in uacuo, at which temperature complete recrystallization occurred without any change in the form of the inclusion. They were then fractured at temperatures from -190" to 600°C. Cup and cone fractures were obtained at all temperatures from -196" to 400°C. With increase in temperature there was, however, a continuous increase in the extent of the central transverse area and a corresponding decrease in the shear portion of the fracture. Above 400°C, the fractures became intergranular. Sections of specimens tested below 400°C revealed extensive small voids which were always associated with inclusions. However, the voids only reached dimensions greater than the inclusion size in the region of the macroscopic neck, where they were many times longer. Lateral expansion was found only near the fracture surface of the test pieces. As observed by Puttick, the voids were either (a) triangular holes initiated in the direction of the tensile axis and elon-

Jan 1, 1969

By L. J. Buteau, R. E. Reed-Hill, W. A. Slippy

In a zirconium {1121} twins tend to have coherelzt boundaries and thus do not usually taper to a point when they intersect a grain boundary. Under the proper conditions, a (1121) twin may deform a boundary in such a manner as to clearly rcveal the twinning shear. Measurements of these grain-bounrlary rotatzons yield a value of 0.63 for the (1151) twinning shear. The magnitude of the observed shear and its shear sense are in excellent agreement with the assumption that the second undis-torted plme (K2) for this form of twinning is the basal plane (0002). The present value of the tzvinninz shear, which is approximately three limes larger than Rapperport&apos;s value? is in excellent agreement with reported results of Sokuskii and Prolsenko.5 RECENTLY westlake&apos; reported a study of the twinning modes of zirconium based on ~ap~er~ort&apos;s2 values for the twinning elements. He observed that two of the modes, (1012) and {1122), can be explained by relatively simple dislocation models. A workable model for (1121) twinning, however, proved to be very complex and questionable. Because Rapperport&apos;s second undistorted plane, (K2), for (1121) twinning has large indices, {ll2l6), it is possible that the difficulty in defining a model for (1121) twinning lies in an incorrect value for K2. A measurement of this twinning element has therefore been made, using a method based on observations of the shear displacement of grain boundaries at positions where they are intersected by (1121) twins. EXPERIMENTAL PROCEDURES The zirconium specimens were deformed in tension on an Instron machine either at the temperature of liquid nitrogen (77ºK), or prestrained at liquid nitrogen temperature and then further deformed at room temperature. Straining at 77°K was employed in order to nucleate (1 121) twins in large numbers, since simple ropm-temperature tensile deformation favors (1012) twinning. Specimens were machined from 1/2-in.-thick plate. The material was arc-melted sponge zirconium annealed to an ASTM grain size 4 and containing, in parts per million, 380 Fe, 880 0, <40 Hf, 32 N, and < 5 H. The specimen gage length and diameter were 1.25 and 0.130 in., respectively. To insure a gage section initially free of twins, the last 60 thousandths of the specimen diameter was removed by acid machining.

Jan 1, 1963

By J. S. Brown, A. G. Guy

With the exception of the work of Tammann and Hartmann,1 no published information has been found on the structural changes produced in eutectic structures as the result of heating following plastic deformation. In part this lack of information may be due to the fact that many eutectic structures contain an intermetallic compound as a prominent phase, and as a consequence have been considered to be unworkable. For example, Tammann and Hartmann were able to obtain useful data only on those alloys that they could greatly reduce in thickness by cold rolling. This restriction placed on the investigation of alloys containing intermetallic compounds has been largely removed by the work of Savitskii2 which showed that large deformations of such alloys can be produced by relatively slow compression at temperatures near the melting range. It was possible, therefore, to carry out the present work on a range of binary eutectics including one composed of two intermetallic compounds. The essential results obtained on the alloy systems studied are illustrated by the Pb-Mg eutectic containing 33.2 pct Mg, Fig 1. The cast structure, Fig la, was obtained by melting together magnesium of 99.8 pct purity and chemically pure test lead, casting into a heated, small steel mold, and furnace cooling in the mold from about the eutectic temperature. The fairly coarse eutectic structure thus obtained was too brittle to work at room temperature without cracking. Fig 16 shows the worked structure obtained by compressing a 1/2-in. cube 70 pct in about 15 sec at 550°F and then water quenching. The pronounced changes in the distribution of the two phases produced by heating the worked alloy at 850°F for 1 hr are shown in Fig lc. Recrystallization of both phases appears to have taken place, and the mechanical properties of the cast alloy must have been significantly changed by the working and heat treatment. Similar results were obtained with the Mg-59.5 pet Bi, Mg-36.4 pet Sn, Mg-65.4 pet Cu, and Bi-40 pet Cd eutectics, only the last of which could be worked at room temperature. Tammann and Hartmann reported a thickening and shortening of the needles of the eutectics which they heated about 10°C below the melting range for 1 hr after drastic cold rolling. They found the following eutectics, given the indicated amounts of reduc- tion, to have a granular structure after heat treatment: Sn-9 pet Zn (98 pet); Cd-82.5 pet Pb (60 pet); and Bi-43.5 pet Pb (90 pet). On the other hand the alloy Al-11.7 pet Si (60 pet) showed no change after heating. Tammann and Hartmann observed a distinct shrinking of the needles in unworked eutectics subjected to heat-treatment. In the present work inappreciable change in the eutectic structure was found on heating undeformed alloys. In summary, it appears that eutectic structures can be recrystallized into a "spheroidized" condition by heating near the eutectic temperature after severe deformation. If the eutectic contains one or more brittle phases the necessary deformation can be accomplished by pressing at high temperatures. It is reasonable to expect that this tendency towards equiaxed grains from the plate- or needle-like eutectic structure should be general since the energy relations and mode of growth in recrystallization are so different from those that hold for eutectic crystallization. References 1. G. Tammann and H. Hartmann: Ztsch. Melallkunde (1937) 29, 141-144. 2. E. M. Savitskii: Doklady Akad. Nauk S.S.S.R. (1940) 62, 349-351. Abstr. in Melal Prog. (July, 1949) 56, 126, 128.

Jan 1, 1950

By Terje Preber

Undisturbed sampling of shale has always been difficult. As pert of a comprehensive subsurface investigation for a nuclear power plant in northwestern Illinois, the Maquoketa shale, which contains seams of argillaceous dolomite, was sampled using different coring techniques. Since the Maquoketa shale is extremely fissile, careful sampling preservation by both lateral and vertical confining was utilized. The samples were tested to determine both static and dynamic properties. A relationship between void ratio and compression index, swell index, and swell pressure ratio was established. Correlation was found between the dynamic properties and both undrained shear strength and confining stress. Based on the results of the sampling and testing programs, recommendations for sampling and sample preservation techniques are given. INTRODUCTION Undisturbed sampling and preservation of samples of weathered, fiasile shale is often a very difficult task. The often erratically varying degree of weathering with depth complicates sampling and makes reproducibility of testing results difficult. Therefore, the testing of weak, weathered rock very often yields a wide variety of test results with large data scatter. The reproducibility of teat results usually associated with water-deposited soils is seldom, if ever, obtained. The testing and sampling program described in this paper was part of a comprehensive subsurface investigation for a nuclear power plant in northwestern Illinois. The sampling, preservation and testing program of shale samples taken from the Maquoketa shale are described, and, in particular, the different sampling techniques and sample preservation procedures are evaluated with respect to their effectiveness. The samples obtained by these procedures were subjected to a comprehensive testing program, including both static and dynamic testing in order to provide input for soil-structure interaction analysis. GEOLOGY The Maquoketa Shale Group is of Ordovician age and is part of the Cincinnatian Series. The area where the shale samples were taken was in a broad sea far from sources of clastic sediments during most of Ordovician time. However, during Cincinnatian time when large deltas in the Appalachian region were being formed, clastic sediments from the east dominated the sedimentation ii. Illinois, resulting in formation of the shale and dolomite shales of the Maquoketa Shale Group (Willman et al., 1975). The geologic unit sampled consists of a greenish gray to gray silty shale containing numerous 1- to 12-inch (2.5- to 30.5-cm) thick interbeds of argillaceous dolomite. The dolomite comprises up to 40 percent of the profile studied. The shale

Jan 1, 1984

By J. L. Huitt, B. B. McGlothlin, J. J. Day

Laboratory tests were made with pure minerals and actual reservoir rock samples to study the effects of hydrothermal (steam m hot water) treatments on reservoir rock properties. These tests showed that hydro-thermal treatment of many reservoir rocks can result in significant rock softening. The softening was attributed primarily to the partial destruction of dolomite and kaolinite and the synthesis of montmorillonite in the presence of excess silica. In many cases, the softening was great enough to cause considerable healing of propped fractures; therefore, a serious reduction in welt productivity could result. In other tests it was found that the addition of ammonia to a hydrothermal treating fluid in a concentration as low as 0.013 Ib/lb of water not only could prevent rock softening but could cause rock hardening. The results of X-ray diflraction analyses of rock samples showed that when ammonia was added to the treating fluid, ammonium-mica and analcite were formed instead of montmorillonite. No significant permeability damage was observed in the sandstones that were subjected to the ammonia-hydro-thermal environment; in some sandstones, permeabifity improvements resulted. INTRODUCTION As the use of steam or hot water becomes more prevalent in well stimulation methods. the need for information on the effects of such treatments on reservoir rock properties becomes increasingly apparent. Several works have been published on high-temperature changes in rock properties,&apos;,&apos; but these are more applicable to in situ combustion operations than to steam or hot water injection processes. The mineralogical literature contains many publications which report on the changes occurring with various pure minerals in hydrothermal systems. A review of this literature denotes the ease with which entirely new, crystalline mineral phases can be synthesized from other minerals in hydrothermal environments at temperatures, pressures and residence times typical of those encountered in oilfield thermal recovery or stimulation processes. Discussions of many of these experiments are given by Deer et al. Grim,&apos; Roy et al., Zen\ and Hawkins.&apos; One of the most significant of these pure mineral studies is the hydrothermal synthesis work of Levinson and Vian" in which montmorillonite was synthesized from naturally occurring minerals; i.e., kaolinite, quartz and carbonate minerals (particularly dolomite). These reactions occurred at 575F in only 2 days and at 300F in 5 days. These results may be applicable to petroleum reservoir rocks since the minerals studied were those which are commonly found in sandstones. Furthermore, the environmental conditions imposed in the studies were very similar to those involved in thermal stimulation of petroleum reservoirs, e.g., steam or hot water injection. Other studies have suggested that weak rocks could be hardened by "electrochemical induration", a process in which an electric current is applied to a clay-containing rock body. These tests can be regarded as hydrothermal treatments since they were conducted in some instances with aqueous solutions and since clay temperatures during the electrical treatment reached a maximum of about 100C. Although a number of studies of the reaction of pure minerals have been reported, very little has been published on the reactions of petroleum rock-hydrothermal systems. No work has been reported on preventing the more detrimental rock changes in rock softening which might occur during the injection of steam or hot water into reservoirs. The studies described in this paper were conducted to provide such information. EXPERIMENTAL APPROACH The laboratory tests included studies of the effect of hydrothermal treatment on core samples from several different reservoirs. The hydrothermal treatments (simulated steam treatments) were conducted with distilled water at 575F, for the most part, for periods of 2 to 6 days. This temperature level was selected because it represented that temperature which would probably prevail in several cases under consideration for steam injection projects. The core samples, as well as the pure mineral samples, were contained in high-pressure stainless steel, autoclave-type pressure vessels. The effects of the hydrothermal treatments were evaluated by measuring the penetrometer hardness, formation rock embedment strength and permeabilities of the core samples before and after the treatments (Fig. 1)&apos;" In addition, the mineralogical changes in the specimens were studied by X-ray diffraction. Concomitant with the core sample studies, the mineralogical changes were studied in greater detail by conducting hydrothermal synthesis experiments with pure minerals at similar temperature levels and residence times. For the most part, samples of finely-crushed pure dolomite.

The world&apos;s production of petroleum in 1926 amounted to nearly 150 million long tons, of which India contributed 0.72 per cent. In 1927, this figure jumped to some 172 million long tons, of which the Indian proportion, on a practically stationary production, fell to 0.64 per cent. In 1928, there was another substantial rise in the world&apos;s production, which reached the figure of over 181 million tons. In 1929, there was another jump to over 202 million tons, but in 1930 the world&apos;s production fell to about 193% million tons, in 1931 to about 187 million tons, and in 1932 to about 183 million tons, while in 1933 the production rose again to about 202 million tons, in 1934 to about 215 million tons, and in 1935 to 233 million tons1. Decreases were shown by Poland, Sarawak, Egypt, Rumania and France. All other important producers showed an increase in production, by far the largest being due to Iraq, as a result of the opening of the pipe line to the Mediterranean. The United States contributed 60.9 per cent of the world&apos;s supply in 1935, Russia 10.7 per cent, Venezuela 9.4 per cent, Rumania 3.9 per cent and Iran 3.1 per cent. In 1928, India contributed 0.64 per cent, which fell to 0.60 per cent in 1929 and rose to 0.62 per cent in 1930, 0.63 per cent in 1931, and 0.64 per cent in 1932, and fell again to 0.62 per cent in 1933, to 0.60 per cent in 1934 and to 0.50 per cent in 1935; her position on the list of petroleum-producing countries fell from eleventh in 1929 to twelfth in 1930 to 1933, her place being taken by Trinidad and to thirteenth in 1934 and 1935, owing to the production by Iraq. The production of petroleum in India (including Burma2) increased slightly from 322,025,280 gal.3 in 1934 to 322,662,336 gal. in 1935, the highest figure in the history of the industry. The increase in 1935 is due to an increase of some 4 million gallons in Assam, almost offset by a decrease of 31/2 million gallons in Burma. This increase in output in 1935 was accompanied by an increase in estimated value amounting to Rs. 22,73,550 (£170,944).

Jan 1, 1937

By Harry W. Antes

The density changes that occurred on annealing cold-worked poly crystalline molybdenum, over the temperature range of 870" to 1630 SC, were determined. Increases in density were observed for recovery and the beginning of recrystallization. An initial decrease in density was observed during re-crystallization. A second decrease in density was observed after recrystallization was completed, as the microstructure changed from columnar grains to equiaxed gvains Both decreases in density were associated with an increase in gain boundary area to volume ratio. The second decrease in density was observed in the annealing range that immediately precedes secondary recrystallization as reported in the literature VARIOUS techniques have been used to identify the recovery, recrystallization, and grain growth processes that occur when cold-worked metals are annealed. As early as 1928 work was conducted that indicated measurable density changes occur when cold-worked single crystals of brass are annealed.&apos; More recently, work by Murphy exhibited a corre- lation of density with microstructural changes observed on annealing cold-worked polycrystalline a brass.2 Other investigators have performed similar work on a brass and copper.324 In reviewing the literature, it was apparent that density work had been limited to fcc materials. Therefore, it was the purpose of this investigation to determine the density changes that accompany annealing the cold-worked bcc material, molybdenum. Two degrees of cold work, 30 and 90 pct reduction of cross-sectional area by rolling, were selected for this study. EXPERIMENTAL PROCEDURE High-purity vacuum arc-cast molybdenum was used in this study, the principal impurity being carbon in the amount of 80 ppm. The final rolling reductions were made at 1200°C in grooved rolls to provide 5/8-in.-diam rod. Density specimens 0.500 in. diam by 1.5 in. long were machined from the bar stock. The specimens were ground to the final dimensions to provide a smooth surface. Density measurements were made using a hydrostatic technique similar to that used by ~urphy.&apos; This type of equipment permitted weighing in liquid immediately after the air weighing. During each weighing the temperature of the air and liquid was controlled to within 0.0l°C. This was accomplished by sealing the analytical balance in an air-tight brass chamber and surrounding it by an insulated wooden case. Preheated air was circulated in the air space between the brass chamber and wooden case by means of a blower. The temperature of the

Jan 1, 1964

By J. P. Newell, R. W. Storey

AUGER mining is a form of continuous mining in that it completely replaces with a one-cycle operation the older conventional cut, drill, shoot, and load method of mining. Relatively new, having been utilized only within the last few years, it is even more continuous in its production of coal than some other forms of continuous mining being practiced in this country today. There are at present coal recovery .augers in operation working along strip-mined highwalls from the outside. This paper will deal with underground mining, specifically with an experiment which was carried out with a machine developed for this purpose. The location of this experiment was in Pike County in eastern Kentucky in the upper split of the No. 3 Elkhorn seam. Coal height was 32 in. and roof conditions were very bad, with 10 in. of soft draw slate coming down with every cut in conventional mining. The coal is high-grade bituminous, excellent for metallurgical coking. Underground auger mining fills a need for a method of recovering coal in thin seams, under bad roof conditions or in split seams. In many cases it might save money by eliminating the handling of excessive quantities of rock. In fact, if the coal can be recovered, as in the case of this experiment, without mixing with any impurities outside the seam, it may be possible to load or ship a satisfactory product with little or no preparation or cleaning expense. The need for some economical method for recovering coal from thin seams is becoming more pressing as the more profitably mined seams are exhausted. Basic Principles of Auger Mining The principles of the auger, or screw conveyor, have long been used in drilling small diameter holes for blasting and other purposes. These same fundamentals apply to large diameter drilling. However, considerably more attention was given to designing a cutting head that would not pulverize the coal and consequently would require a minimum of power to drive it. The head, as designed for this job, consists of a cylinder 25 in. in diam with steel bits set in 3 positions spaced around the forward rim. A conventional coal drill bit, at the head of a bursting cone in the center of the cylinder, trails the forward rim slightly, see Fig. 1. The bursting cone and auger connections are anchored to the cutter barrel by 3 arms spaced at 120 This head design proved to be very satis-

Jan 1, 1952

By J. J. Frawley, W. J. Childs

PREVIOUS studies have shown that if a supercooled liquid metal was perturbed by vibration the probability of nucleation is is During a recent investi- gation to determine quantitatively the amount of energy needed to cause nucleation in a given supercooled liquid specimen, it was found that at low-energy values in the megacycle range, below the threshold energy value for cavitation, the amount of dynamic supercooling was greater than the amount of static supercooling. That is, if a specimen had a given amount of thermal supercooling under static conditions, its thermal supercooling could be increased by the addition of low-energy sound waves. The material used in this investigation was high-purity bismuth. This material was chosen because of its low melting point and the high degree of supercooling which could be easily obtained. The sound gener- ator employed in this work was a commercially built Sperry ultrasonic testing unit. This unit was equipped with a barium titanate crystal as a piezoelectric transducer. These sound waves were transmitted to the supercooled melt by a Pyrex rod, as shown in Fig. 1. The transducer was coupled to this Pyrex rod wave carrier by motor oil. The Pyrex wave carrier was approximately 1.5 ft long to prevent damage to the transducer by heat. The diameter of the Pyrex wave carrier appears to be critical. In the initial tests a wave carrier of 0.5 in. in diam was employed. However, the sound waves had no effect on the amount of dynamic supercooling. When the diameter of the wave carrier was increased to approximately the inside diameter of the Pyrex crucible, the sound waves were more effective. Approximately 200 g of metal was melted under a stannous chloride flux in a 30-ml beaker by induction heating. The temperature was recorded by a Pyrex-encapsulated chromel-alumel thermocoule which was placed in the beaker after the bismuth melted. The Pyrex wave carrier was immersed slightly below the surface of the liquid bismuth and the specimen was reheated to about 500°C. It was observed that the amount of supercooling depends on the amount of superheating the specimen receives; therefore, for meaningful results the amount of superheating was the same for all heating cycles. The specimen was allowed to cool in air and the change in temperature was continuously monitored with a potentiometric strip-chart recorder.

Jan 1, 1969

By E. W. Stewart, G. P. Conard, J. F. Libsch

The effects of several additives upon the reduction characteristics of hydrogen-reduced ferrous formate are described. The various additives inhibit sintering of the reduced iron particles by apparently different mechanisms. The magnetic properties of the low density compacts produced from the resulting ultra-fine iron powders were improved markedly. THE permanent magnetic characteristics of ultra-fine iron powder prepared by various means have been a subject of considerable interest and experimentation in the past few years. When such particles are small enough to show single domain behavior, they possess&apos; 1—permanent saturation magnetization, and 2—high coercive force. In the absence of domain boundaries, the only magnetization changes in a particle occur through spin rotation which is opposed by relatively large anisotropy forces. With decreasing particle size, the coercive force tends to increase to a maximum and then decrease because of the instability in magnetization associated with thermal fluctuations. Kittel&apos; has calculated the critical diameter at which a spherical particle of iron can no longer sustain domain boundaries or walls to be approximately 1.5x10-&apos; cm. Stoner and Wohlfarthr in England and Neel4,6 in France have shown from purely theoretical calculations that the high coercive force expected from single domain particles is dependent upon crystal anisotropy, shape anisotropy, or strain anisotropy contributions. Further work by Weil, Bertaut,&apos; and many others has contributed much to the understanding of fine particle theory. Neel and Meikeljohn" have demonstrated that a decrease in particle size below a critical value of approximately 160A leads to a quite rapid decrease in coercive force because of the prevention of stable magnetization by thermal agitation. Lih1, working with powders prepared by the reduction of formate and oxalate salts of iron, has shown the marked influence of powder purity upon magnetic properties. Maximum coercive force was obtained in powders of approximately 65 pct metallic iron content while the maximum energy product, (BxH) occurred in powders of 85 pct metallic iron content. Careful consideration of the preceding theoretical considerations and experimental results has led to the manufacture of permanent magnets from ultra-fine ferromagnetic powders by powder metallurgy techniques. Such work has been done by Dean and Davis," the Ugine Co. of France, and Kopelman." The aforementioned work of Kopelman and the Ugine Co. was concerned somewhat with the effect of various additives upon the properties of hydrogen-reduced ferrous formate. Virtually no work, however, has been published on the effects of additives on the reduction rates of metal formates, although unpublished work by Ananthanarayanan16 howed promise of improved energy product in ultra-fine iron compacts prepared by the hydrogen reduction of a coprecipitated mixture of magnesium and ferrous formate. After consideration of the preceding information, it was hoped that a better balance between the metallic iron content and particle size of the reduced iron powder could be accomplished by a prevention of the attendant sintering of the partially reduced iron powder during the reduction reaction. It appeared possible that magnesium oxide might interpose a mechanical barrier between adjacent iron particles and prevent their sintering together, while metallic cadmium and metallic tin would interpose a liquid barrier which might accomplish the same purpose. The degree to which these materials were effective in accomplishing the foregoing objective and the experimental details associated with the work are reported in the following sections of this paper. Experimental Procedure Preparation of Formate and Oxide Mixtures: To obtain ferrous formate of reproducible reduction characteristics, a slight modification&apos; was made in the technique of Fraioli and Rhoda." A supersaturated solution of ferrous formate was mixed with an equal volume of 95 pct ethyl alcohol and the formate crystals precipitated by stirring and screened to —325 mesh. These crystals were in the shape of elongated hexagons, approximately 4x10 micron in dimension. Various preparations of such ferrous formate, designated as lot 111, were reduced for 2 hr, yielding ultra-fine iron particles of exceedingly reproducible size, metallic iron content, and magnetic properties. The magnesium and cadmium formates were prepared by the reaction of dilute formic acid with their respective carbonates, while the tin formate was prepared by the reaction of dilute formic acid with stannous hydroxide. To evaluate the effect of metallic formate additives in intimate mixture with the ferrous formate, varying amounts of magnesium, cadmium, and tin formates were coprecipitated with the latter. The designations of these materials and their chemical compositions are given in Table I. Due to the differing solubilities of the various formates in aqueous media,

Jan 1, 1956

By Frank A. Wardlaw

MY subject covers the effect that recent metallurgy has had on operations at the Utah-Delaware mine. This mine is the old Highland Boy mine of Bingham Canyon, Utah, one that has now been in operation for about 30 years. It was first operated by Messrs. Weir and Newhouse as a gold mine, under direction of the Highland Boy Gold Mining Co. The ore was oxidized gold ore and it was treated on the property in a cyanidation plant. During the process of development, sulfide ore was found assaying about 5 per cent copper. It proved to be the discovery of what is yet the largest sulfide copper orebody in the State. The first shipment was made in December, 1896. A smelter was built in Salt Lake Valley to treat this ore and not long after the property was sold to the Utah Consolidated Mining Co. From 1900 to 1924, the mine was a large producer of direct-smelting ore which averaged for many years 4.5 per cent. copper, then later dropped to 2 per cent. copper. During the years 1912 to 1920, direct-smelting lead ore was also mined. In 1918&apos;and 1919 ore developments at depth showed a decided increase in silica content and a porphyry sill so closely associated with the ore that it was impossible to mine the ore clean and it was found necessary to build a copper flotation Eoncentrator at Tooele. The mill had a capacity of 1000 tons a day and made a recovery of 90 per cent., and would have been responsible for a continuance of profitable operations had it not been for a slump in the copper market and the necessary high cost of mining ore on the lower levels. RESULTS OF SELECTIVE FLOTATION In 1924 the mine was on the point of a shutdown which had all the earmarks of being permanent; it was being operated at a heavy loss and preparations were made to pull the pumps and salvage the machinery. The plant at Tooele was remodelled for selective flotation by the Inter- national Smelting Co. in order to treat custom ores, and incidentally to clean up a possible 10,000 tons of lead-zinc ore which it was thought possible to get in the Utah-Delaware before shutting the mine down. Results were so encouraging that an effort was made to develop more lead-

Jan 1, 1928

By W. L. Chu

It was observed that chromized coatings on low carbon steel could be embrittled by cooling slowly through the 475°C range. A higher chromium coating was more susceptible to embrittlement than a lower chromium coating. Coating structure and composition could be correlated with the chromizing process and prior carbon content of the steel. IT was recently observed that during the fabrication of rectangular tubings made with chromized thin gage 1010 steel, a high percentage of these parts were fractured readily in a brittle manner under the light impact-forming load employed. Ensuing investigation indicated the cause for such brittle failures to be the so-called 475°C embrittlement of the chromized coatings. The experimental work and results are briefly reported. Rectangular tube sections of normalized AISI C1010 steel, which had a cross-section of 0.5x1.5 in. and a wall thickness of 0.030 in., were chromized to yield coatings having several ranges of thickness, varying from 0.0005 to 0.002 in. Essentially, the chromizing process is similar to that described by Samuel and Lockington,&apos; which consists of heating the parts in a sealed container at about 955°C for 4 hr in intimate contact with a chromizing mixture* samples in a hydraulic press, and the other employed a simple beam bending test of the flat sides of the tubing walls. Neither, however, was able to differentiate the relative brittleness of samples known to include both the brittle and tough types, since the impact-brittle samples were found to deform readily in a manner similar to the tough ones. Both the tough and brittle samples were studied by reflection microscopy. Observation showed that the microstructures of the steel cores were similar in content and distribution of inclusions as well as in the ferritic grain size. Results of Filar micrometer measurements showed that coating thicknesses+ of the brittle samples averaged 0.0007 in., whereas those of the tough samples averaged 0.0016 in. The micrographs of Fig. 2 illustrate the structural differences between coatings of both types of samples. By dissolving the steel cores in nitric acid, coatings of both the brittle and tough samples were isolated. Simple bending tests showed that coatings of the brittle samples cracked readily at about 90" bend, whereas those of the tough samples could be bent nearly 180° without cracking. The coatings as well as the steel cores were analyzed for carbon and

Jan 1, 1956

By A. M. Nicholas

WheN attempting to lift mill pulp containing a considerable percentage of wolframite, in an ordinary bucket elevator, difficulty was encountered from the tendency of the tungsten minerals to settle, on account of their high specific gravity. Lifts not exceeding 20 ft. (6 m.) could be accomplished without particular difficulty, because there was insufficient time for consolidation of the heavy minerals in the bottom of the bucket; but with higher lifts, the heavy tungsten minerals would settle so solidly that when the bucket turned over at the top of the elevator the contents could be only partially dumped. In this case it was necessary to lift the material a distance of 34 ft. (10m.); hence some means had to be adopted to prevent settling, at least to such an extent that the material could be dumped from the buckets. To reduce the carrying time to a sufficient extent would have required a belt speed of 475 ft. (144.7 m.) per minute, which was not feasible. It was decided to try, by vibrating the belt about midway of its span, to keep the material sufficiently agitated during elevation to prevent settling. Underneath the rising side of the belt was placed a 12-in. (30.48-cm.) idler pulley, 18 ft. (5.5 m.) up in the total lift of 34 ft. The idler pulley was set eccentric by % in. (19 mm.) and it was hoped that the vibration thus imparted to the belt, running at a speed of 280 ft. (85 m.) per minute, would prevent settling in the buckets. It was found that the pressure of the belt on the idler, due to the small inclination of the elevator, was not sufficient to overcome sliding on the idler, and the agitation was insufficient to accomplish the desired purpose. The idler was then connected to the drive shaft of the elevator through an intermediate pulley, gearing down to a speed of 20 r.p.m., so that a positive vibration was imparted to the belt; this imparted enough motion to the belt to prevent settling and the contents of buckets dumped satisfactorily. Protecting Elevator Belts When elevating, from the crusher, a rock which was very sharp and abrasive, considerable difficulty arose from cutting of the belt under-

Jan 1, 1918

The Nominating Committee desire to submit the following nominations. President and Director: SIDNEY J. JENNINGS District 0 Vice-President and Director: H. S. DRINKER District 2 R. M. RAYMOND District 0 Directors: G. C. STONE District 0 HENNEN JENNINGS District 9 S. A. TAYLOR District 2 F. G. COTTRELL District 6 ARTHUR THACHER District 3 These nominations were unanimous. By order of the Committee J. V. N. DORR, Chairman. Oct. 10. 1917.

Jan 12, 1917

By Claude H. P. Lupis, John F. Elliott

WAGNERL described the thermodynamic behavior of a metallic solution consisting of the solute components 2, 3,... at very dilute concentrations in the solvent, 1, in terms of the excess partial molar free energy, or alternatively the logarithm of the activity coefficient. In the Taylor expansion of FiE, by neglecting the second- and higher-order differential terms, he obtained the excess partial molar free energy as a linear function of the composition:

Jan 1, 1965

By Robert M. Betts

The Cornucopia district is situated in northeastern Oregon 25 miles from the Snake River branch of the Oregon Short Line R.R. and 75 miles northeast of Baker City, in the Wallowa Mountains. The formation is principally granodiorite, which has intruded much older rocks locally known as greenstone, and which are probably altered schists. In the upper horizons of the veins, greenstone is found as inclusions in the granitic mass. Both of these formations have been cut by numerous basalt, aplite, and porphyry dikes. Veins of the district are the result of faulting and the consequent crushing of the wall rock. The ore has been deposited irregularly along these faults and formed a lenticular type of vein. The ore varies in width from a few inches to 20 ft.; the average stoping width is about 5 ft. As the basaltic dikes are subsequent to the ore deposition, they are at times a hindrance in development and mining operations; on the other hand, a dike which has followed a vein as a line of least resistance often serves as a good mall in place of the crushed, rather loose granite. The veins generally strike northeast-southwest and dip about 35" to the west. Orebodies are from 100 to 300 ft. in length and about the same in height. The lenses are irregular; inclusions of wall rock are common in the ore and are a factor in reducing the grade. The ores are quartz, carrying some free gold near the surface, but the metals for the most part are in iron sulfides, sometimes associated with chalcopyrite. The gold and silver are in a mechanical combination with the iron, which requires find grinding to liberate them. The ratio of silver to gold is 5 to 1, by weight. Development The Cornucopia Mines Co. owns, and operated until 1920, two mines and two mills of 100 tons capacity each. The sustained high costs and labor shortage, however, necessitated the abandoning of the Union mine, the oldest in the district. Two crosscut tunnels were then started, first, to cut the Last Chance vein at a much lower horizon and, second, to prospect two parallel veins. The ore from the Last Chance vein will go to the old Union mill and the ore from the new veins to the Last Chance mill.

Jan 1, 1925

By M. C. Flemings, T. S. Piwonka

Pore formation is examined analytically in cellu-larly solidified single crystals, in cylindrical castings of pure metals and alloys, and in unidirectionally solidified castings. Effects are considered of fluid flow. dissolved gas, and surface tension. Experimental results show that flow through a partially solid "mushy" aluminum alloy obeys relations similar to those applicable for flow through other types of porous beds. Flow rate is proportional to the square of the fraction liquid (fL) for fL less than 0.3. Results indicate models chosen for mathematical description of pore formation in alloy solidification are valid. ONE of the solidification variables which is influential in determining mechanical properties of castings and of wrought material produced from cast ingots is porosity. This porosity may result from shrinkage, dissolved gases, or a combination of both, and may take the form of either macroscopic pores in localized areas of the casting or microporosity evenly distributed throughout large areas of the casting. In alloys which freeze over a range of temperatures some microporosity is generally found after solidification. There has been much discussion as to whether the micropores are caused primarily by shrinkage, by gas, or by a combination of both.&apos;-3 There has, however, been little experimental or analytical work performed to delineate the relative contributions of shrinkage and gas in causing microporosity or to quantitatively describe the influence of processing variables on microporosity. Porosity other than microporosity (e.g., center line shrinkage) has also received only limited quantitative treatment.495 The aim of this work is to examine analytically the general problem of pore formation in solidification and to perform limited confirmatory experiments. Consideration is first given to shrinkage porosity in pure and nearly pure metals (shrinkage in cellular growth, centerline shrinkage in cylinders). Next, a discussion is given of formation of shrinkage-caused microporosity in unidirectional solidification and in "mushy" solidification. Finally, influences of dissolved gas and surface tension on microporosity are examined. Numerical results are given for aluminum and an aluminum alloy. Typical examples of microporosity are shown in Figs. 1 to 3, for 1) cellularly solidified aluminum, 2) sand-cast aluminum alloy, and 3) low alloy steel. SHRINKAGE POROSITY IN PURE AND NEARLY PURE METALS 1) Cellular Growth. In cellular freezing of an impure liquid, liquid grooves may exist over a considerable length of the growing crystal.6 The cross-sectional area of the grooves decreases with increasing distance from the cell tips; the root of the groove is blunt if the liquid at this point reaches eutectic composition. As a result of volume contraction during solidification, flow occurs down the groove, parallel to the growth direction; hence, there must be a pressure drop from the groove entrance to points within the groove. The geometry of the groove is simplified to that of a circular cylinder of radius r and length L, Fig. 4, L » r, and a simple and useful limiting case is obtained. This is that, in the circular cylinder freezing at constant velocity, the pressure at the root of the groove is lower than that pressure at radius r in grooves of other geometries where r decreases continuously to a lower limit at L. As discussed below, a pore resulting from a given pressure difference

Jan 1, 1967

By L. S. Darken

A quadratic formalism is developed lor the representation of the excess free energy, and of the activity coefficients of each component of a ternary system in the vicinity of a single component selected as solvent. This formalism, in contrast to the e formalism, is thermodynamically consistent at .finite concentrations. Numerous specific systems are used as illustrations, with cross checks where possible; these systems are Fe-C-X systems in the vicinity of 1600°C and include practically all those for which reliable data are available. It is shown that this formalism is usually quite adequate to rebresent available data up to a solute concentration of 20 to 30 at. pet. It is hoped that the formalism here presented may prove useful for the treatment and tabulation of data on ternary and multi-component solutions. SINCE, as discussed in a prior paper,&apos; we do not as yet have an adequate basic understanding of the nature of binary metallic solutions, we cannot hope to be in better position for ternary and multicomponent systems. However, the accumulation of thermodynamic data on ternary and multicomponent metallic solutions has led to an urgent need for a rational formalism for the presentation and use of such data. Notable attempts to represent the isothermal isobaric thermodynamics of ternary solutions were made by Benedict et 01.&apos; and by Wohl.3 These attempts were directed toward developing an analytic expression adequate to encompass the entire ternary triangle, primarily for organic systems; they generally involve the power-series approach, which has been shown&apos; to be inappropriate, in general, even for binary metallic systems. On the other hand, interest in the thermodynamics of ternary and multicomponent metallic solutions has tended to focus either on general thermodynamic relations4-10 over wide compositional ranges, or on cases where one or more components have been at rather low concentration. This latter approach has been followed by Wagner,= by chipman,11 and by Alcock and Richardson,12 and more recently in many publications by the same and other authors. It has already been shown&apos; that the thermodynamic behavior of binary metallic systems is, in general, relatively simple only in the terminal regions. Hence, it would appear that any approach, at this time, to a simple formalism for ternary and multicomponent systems must, a fortiori, be limited to the vicinity of the major component or solvent. The present treatment is aimed to be useful for a given solvent with moderate solute concentrations ranging up to 20 or 25 at. pet and in exceptional cases to considerably higher concentrations. In order to achieve even this modest objective, it is necessary that any appropriate formalism have built into it 1) a thermodynamic consistency (at least within the desired degree of approximation), and 2) an approach at infinite dilution to Raoult&apos;s law for the solvent and to Henry&apos;s law for each solute. Let us first formulate the condition of thermodynamic consistency for a ternary system. Under isothermal isobaric conditions, we may write for the molal value G of any extensive function dG - C1 dN1 + G2 dN2 + G3 dN3 [l] where the G&apos;s are the corresponding partial molal quantities and the N&apos;s are the atom fractions. Taking component 1 as the solvent, this relation may be rewritten in terms of the independent variables N2 and N3

Jan 1, 1968

By R. B. Falk, F. E. Luborsky

Small iron particles in mercury pow by diffusion of iron atoms through the mercury. Iron particles, with diameters about 200Å, have been stopped from gvowing in size, even up to the boiling point of mercury, by the addition of a third metal. The metal additives were classified according to whether they produced 1) negligible inhibition, 2) some inhibition, or 3) marked inhibition of the growth rate. Metal additives which resulted in a marked inhibition of iron-particle growth form a stable monolayer on the iron particles. Only those metals which may form compounds with iron showed this pronounced effect. The one exception was manganese. Metal additives which resulted in no inhibition of growth, showed no evidence for adsorption and could not form compounds with iron. None of the added metals, even those which strongly inhibited particle gvowth and thus had adsorbed on the particle surface, actually formed any compounds with iron at room temperature at the concentrations required for complete inhibition of growth. ThE stabilization of the size and shape of metallic particles dispersed in liquid metals has important technological implications in "homogeneous" nuclear reactor systems and in elongated particle magnets and is directly related to the problem of corrosion by liquid metals. Growth in these par-ticulate systems may occur by diffusion of atoms from surfaces of high energy, corresponding to a small radius of curvature, to surfaces of low energy or large radius of curvature. Thus, small particles dissolve and large particles grow to increase the average diameter of the particles. reenwood&apos; has analyzed this diffusional growth of a system of particles containing a distribution of sizes and has obtained reasonable agreement with data on the growth of uranium particles in liquid sodium and UPb3 particles in liquid lead. Greenwood concluded from his analysis that the chief factors promoting stability of dispersed particles growing by a diffusion mechanism are large mean radius, high density, and low molecular weight with low values of the solute diffusion coefficient, the solubility, and the interfacial tension. In the case of elongated particle magnets the system of interest is that of iron particles dis- persed in mercury. Previous work,2 concerned with "spherical" particles in mercury, has indicated a diffusional growth mechanism similar to that discussed by Greenwood. It has also been shown3&apos;4 that the addition of certain metals to Fe-Hg dispersions results in the formation of a monatomic layer of adsorbed atoms on the iron particles. In this paper we will show that this adsorbed layer provides the decrease in the iron-atom flux through the mercury necessary for size stabilization. The general features of the stabilization of the iron particles in mercury through the formation of this "coating", with many different metals, will be described. EXPERIMENTAL RESULTS Iron particles in mercury were prepared by elec-trodeposition,2, 4 and measurements2, 4 of coercive force HCi) and saturation induction (Is) were used to follow changes in size and composition during thermal aging in the mercury in the presence of relatively small amounts of an added metal. In Fig. 1 is plotted the aging behavior of spherical particle samples in the presence of some of the added metals to be discussed. The iron particles have an initial average diameter of 180Å. Each sample was aged for 20 min at each temperature in succession in the presence of a twofold to threefold excess of added metal over that required to form a monolayer on the iron particles. These are the same samples used previously3 to study the adsorp-

Jan 1, 1965

By D. M. Boulin, E. S. Greiner

Single crystals of vanadium were bent at 293" and 77°K to a maximum fiber strain of about 1 pct. Analysis of slip line and etch markings of- crystals deformed at either temperature show the slip planes are {112}. The slip directions at 298° and 77°K, deterwined from the asterism axes of rotation of crystals compressed in a {110} direclion, were (111). Etch pits, associated with dislocations, were observed in the plastically deformed vanadium. There was no evidence of mechanical twinning. THIS paper presents results on single crystals of vanadium plastically deformed by bending and compressing at 298° and 77°K. Bcc metals have been observed to slip on {110}, (1121, and (123) planes while the slip direction has invariably been found to be ( 111) 1 Lindley and smallman2 have studied the deformation intension of polycrystalline vanadium between 298° and 20°K and reported that at and above 77°K the deformation is predominantly by slip, but at 20°K the deformation is associated with twinning. Later, Edington and smallman3 found that single crystals of vanadium compressed in a (111) direction at 77°K deformed by twinning on { 112}( 111) systems. Clough and pavlovic4 have reported that mechanical twins were observed in vanadium loaded by impact at 77°, 173°, and 195°K, respectively. PREPARATION OF SINGLE CRYSTALS The vanadium single crystals were made from commercial vanadium reported to contain 0.03 pct C, 0.03 pct 0, 0.02 pct N, 0.0X* pct Ca, 0.0X pct Si, proximately 0.8 cm diam, 4 cm long and were grown in (100) and (110) directions. A crystal for studies of etch pits was gound to have a face parallel to a {l00} plane by the Bond crystal-orienting technique.7 In order to avoid straining, the crystals were placed on the steel mount with a low-melting organic compound (glycol phthalate) before grinding. Crystals for the bending experiments were ground to have the four side faces parallel to ( 100) planes. The crystals were electropolished8 in 10 pct H2So4 using a current density of about 3 amp per sq cm to remove the strained surface material. The crystals were bent slowly by three-point loading in a stainless-steel jig designed by Sylwestrowicz.9 The end rollers of the jig were 3.8 cm apart. DEFORMATION AT 298°K The bent vanadium crystal, after removal from the jig, had a radius of curvature of 20.4 cm over the 2-cm length close to the center loading roller, where the maximum bending moment occurred. This radius of curvature corresponded to a maximum fiber strain of 0.9 pet. The side faces contained slip bands as shown in Fig. 1. These bands are straight where the strain is high, top and bottom of micrograph, but are curved on either side of the neutral axis in the center. This curvature of the slip bands in the low-stress area may be due to cross slip. The plastically deformed crystal was subsequently electropolished and then electroetched in 10 pct H2SO4 solution, using a current density of 0.25 amp per sq cm. The structure is shown in Fig. 2. The directions of the traces on two adjoining faces were plotted stereo graphically, Fig. 3.* Since there were two sets of

Jan 1, 1968