Search Documents

By Gerhard Finstermann, Ichiro Maeno, Takehiko Saito, Hironori Shimogama, Konrad Krimpelstätter

Automobile manufacturers are developing Electrified Vehicles with light steel body structure designs that reduce mass and therefore greenhouse gas emissions over the vehicle’s entire life cycle. This raises the demand for the production and development of Advanced and Ultra High-Strength Steels (AHSS / UHSS) and Electrical Steels with increased permeability and reduced core loss to improve energy conversion efficiency. To meet this requirements the steel market is tending towards new generations of AHSS with improved formability (3rd generation AHSS) and high-silicon steels with higher strength and thinner products. With this growing demand for advanced high-strength steels and electrical steels, producers are faced with a unique and interesting challenge in producing materials that strain or exceed the capabilities of existing mill equipment and automation designed to produce low- to medium-carbon sheet. While specialty steel producers have known for decades how to process special high-strength steels and thinner gauges, this equipment typically does not offer the yield and productivity desired by the market, necessitating innovation in re-engineering existing equipment to meet the market demands more economically than new construction. In the case of cold rolling, this can be supported through variable roll geometries, more effective roll-gap lubrication technologies, application of strip heaters (Warm Rolling) to reduce risk for edge crack propagation and strip breaks as well as continuous rolling managed by state-of-the-art automation technologies.

Oct 1, 2019

By Gergö Rimaszéki

Due the fast growing of pig iron and steel in the last years associate with some mineral resources changes (Hematite?Itabirite), has been checking the sinter feed degradation. The typical sinter feed (0.15;-6.3 mm) has become limited and the rapid growing production resulted in more and more fine ore (< 150 µm) availability in the market. The sinter plant operators are facing several new challenges since the mixing and granulation- and the sintering behavior of the fines containing mixtures often differs from the traditional sinter feed´s behavior. The utilization of fines in the sinter plants might increase the process water consumption required for the mixing and granulation process or even the solid fuel consumption, which effects the operational cost of the plant significantly. The current study presents an overview about Outotec´s laboratory facilities and competence regarding the mixing and granulation of fines in different equipments. The usage of high intensity mixers (HIM) – vertical and horizontal as well – showed to be the most effective, based in cold agglomeration tests in small scale, in case of fine ore handling. Permeability and particle size distribution curves are used to evaluate and demonstrate the efficiency of the different equipments. Outotec´s ”Know-How” with the different type of mixer and the modern laboratory facilities provide an excellent opportunities to optimize the mixing and granulation procedure and utilize up to 100 % pellet feed

Aug 17, 2017

By Paulo Rodrigues dos Santos Junior, Luciano Passos de Jesus, Vagno Dordenoni Beltrame, Vinicius Antonio Ramos Pin

Faced with an increasingly demanding and selective market, a thorough analysis of each step of the processes is required in order to achieve high levels of performance. In addition to a major factor of importance in the rolling process, due to its high price, the rolls represent one of the main items in the cost of hot coils production. Using the 6 sigma methodology, there were opportunities for improvement in the grinding process, fatigue analysis, improvement in NDT in rolls, as well as means to guarantee operational stability, which allowed the reduction of roll’s consumption and consequently the cost of production.

Oct 11, 2019

By Baoliang Xiao, Hui Pan, Yajun Hui, Kun Liu

The microstructure, properties, strengthening mechanism and work hardening mechanism of 600MPa grade high ductility hot-rolled sheet steel for automotive square tube were investigated by utilizing optical microscopy, scanning electron microscopy and transmission electron microscopy. The results show that the microstructures of low C-low Mn-Nb and Ti microalloyed steel (Steel A) and high C-high Mn-Nb microalloyed steel (Steel B) are composed of ferrite and a small amount of pearlite. Compared with steel B, the size of ferrite and pearlite of steel A is finer, while the size of the second phase precipitates is larger. The mechanical properties of the two tested steels are similar before tube forming, except that the yield ratio of steel A is higher. Steel A has/exhibits significant work hardening after tube forming; the yield strength and tensile strength increase by 45 MPa and 26 MPa, respectively, while the elongation decrease by 6.0 percent. The yield strength and tensile strength of steel B increase by 22 MPa and 10 MPa, respectively, and the elongation decrease by 4.0 percent. The grain refinement strengthening is the dominant strengthening mechanism, accounting for 52.9 to 61.8 percent of the total yield strength; the solid solution strengthening is the second strengthening mechanism, accounting for 17.2 to 25.3 percent, while the precipitation strengthening and dislocation strengthening contribute little to the yield strength. The dislocation strengthening increase by 82 MPa of steel A after tube forming, which is higher than that of steel B. Therefore, steel B has a low work hardening rate that is more suitable for manufacturing automotive square tube for secondary tube forming.

Oct 1, 2019

By Klaus Pronold

Once installed rolling mills can look forward to a long life. Around 40% of the 140 conventional hot strip mills presently in operation were built between 1960 and 1970. 17 of the 29 CSP®-plants were commissioned before the year 2000 and have automation platforms that are obsolete and/or have outdated rolling technology. Keeping pace with the market requirements is an ongoing challenge for producers of flat steel. It is a real balancing act keeping production facilities performing at necessary levels, safeguarding the investment and keeping outage periods to a minimum. To overcome these demanding factors and strike the right balance allowing for the production of higher grade steel that meets the current market price the installation of mechanical equipment as well as automation platforms and process technology must meet the latest technology standards. Being discussed in this paper are the different motives for modernizations along with their impact on project handling and commissioning philosophies. Experience gained during recent modernization projects in the field of flat steel rolling relating to Steckel / plate mills or current CSP® modernizations will be shared and demonstrate that each modernization has its own individual solution. Specific strategies are explained to help optimize production, increase plant agility and maximize the return on investment.

Aug 17, 2017

By Stephanie L. Kaster, John G. Speer, Blake M. Whitley

Niobium-microalloying technology has been increasingly applied in a wide range of steel applications over the past half-century, to increase strength, control microstructure, enhance properties and enable a variety of applications. To achieve desired performance levels, thermomechanically processed microalloyed steels are widely supplied by the steel industry for high volume applications in hot-rolled plate, sheet and structural steels. However, in steel long products and forgings, the final properties are often generated by downstream users, after heat-treatment, surface hardening, forging or wire drawing. Two examples are presented highlighting advancements associated with Nb-microalloying, to enhance microstructures and properties developed during thermomechanical and/or downstream processing. In the first example, a 0.02 wt. pct. Nb addition was made to a medium-carbon bar steel intended for induction-hardening applications requiring fatigue and fracture resistance in bending and torsion. The Nb addition as well as thermomechanical bar processing led to beneficial refinement of both the pre-induction and post-induction microstructures. In the second example, a 0.01 wt. pct. Nb addition to a high-carbon wire rod was found to refine the pearlite colony size and interlamellar spacing, and increase the hardness.

Oct 1, 2019

By Jianping Li, Fei Peng, Yunbo Xu, Jiayu Li

In this study, in order to achieve ultra-high strength without reducing plasticity, a novel heat treatment involving a pre-quenching process prior to conventional intercritical annealing (P-IDP) was proposed in a low carbon low alloy DP steel. It revealed that abundant fraction of banded structure was observed after conventional intercritical heat treatment (IDP) due to the inheritance of cold rolling deformation. However, the banded structure in novel heat treatment was eliminated significantly, whilst the refined microstructure was relatively more homogeneous with ultrafine ferrite grains. Moreover, obvious chain-networked martensite grains along the ferrite grain boundaries were obtained. The optimum mechanical properties with ultimate strength of 1238 MPa, total elongation of 17%, product of strength and elongation (PSE) of 21GPa% were obtained by P-IDP treatment, which was much higher than the values reported with similar composition. As to pre-quenching treatment, all of grain refinement, homogeneous distribution of martensite islands and precipitated strengthening of microalloyed carbides were beneficial to improve the final strength and ductility.

Oct 1, 2019

By Bruce V. Kiefer

A modernization project was undertaken by Kroman Celik Sanayii A.S. in order to improve their product quality, consistency and shape of the coil package, reduce maintenance and delays in rod mill, thereby increasing utilization and productivity. The project involved installation of a new Morgan Intelligent Pinch Roll and High Speed Laying Head, modifications to the existing controlled cooling conveyor, plus replacing the coil reforming station. The new pinch roll and laying head were to provide better control of the ring formation and consistency of the coil on the conveyor, while reducing delays on the conveyor. Changes to the controlled cooling conveyor included installation of new nozzle decks and Optimesh air distribution system along with re-arrangement of existing fans in order to improve both cooling rates and uniformity of cooling. This paper explains details and features of the newly-installed equipment technology. Resulting product and process improvements are presented, including increased tensile strength and uniformity, reduction in delays on the conveyor and reform tub, plus improvements in coil quality.

Oct 30, 2017

By Manfred Hackl, Sergey Bragin, Alois Seilinger

The demand for hot rolled strip is growing in multiple ways. To remain competitive, new and existing mills must meet arisen challenges in the best possible way. The production of hot strip is a key element of steel production. Since close to half of all steel produced is hot-rolled to strip, mills require maximum throughput and availability combined with geometrical precision and the ability to create optimum material properties. Today there is a clear trend in developing new steel grades with high-strength and improved formability, like 3rd generation AHSS (Advanced High Strength Steels), as well as a trend to produce thinner and wider gauges. This trend challenges hot strip mills because it requires new technologies which provide more flexibility in metallurgical treatment during the rolling process. In order to meet and promote these trends Primetals Technologies is currently working on different concepts and solutions. One example is the development of a new mill stand technology Flex-HI HOT which allows to adapt the last finishing mill stands by efficiently switching from 4-high to a 6-high mode with small work roll diameter based on production needs. Another solution is to apply a permanent 6-high rolling stand at the end of the finishing train. A smaller work roll diameter allows to achieve higher specific thickness reductions and deformation rates resulting in significant thinner hot-strip gauges with valuable metallurgical benefits. The developed solution concepts with technological and metallurgical benefits will be presented in this paper.

Oct 1, 2019

By Patrick E. Connell

During the ABM Conference of 2015 the latest design and process features of the new 3-roll RSB® generation were presented together with a unique Size Control System SCS® for a real time closed loop control to produce an extraordinary quality SBQ – day in, day out. In the past two years, Kocks has focused on improving the repeatability of the rolling process and developed technology to enhance the performance of its equipment. These developments include Fast Remote Control (FRC), Stands Adjustable Under Load (AUL) implementation of closed loop Size Control System (SCS), and finally a state of the art laser Gauge (4D Eagle) that pulls all of these developments into a complete package of quality. Gauges used in the past generally operated with the “shadow” measuring system. The latest gauge developments are based on the “light section” method. This method is more suitable to provide real time measurement parameters of the rolled bar. Placed close to the last rolling stand, the “light section” gauge is capable of measuring around the complete diameter with a clear definition of the bar stage in relation to the axes of the rolls. It is also capable of making these measurements using a very high measurement frequency. Following requirements of the market, requiring the highest gauge measuring frequencies which display the bar in the most accurate way even at the highest rolling speeds, the “4D Eagle” gauge was developed. This paper describes all the process features and parameters of this impressive and unique newly developed gauge as well as the other described technical improvements.

Oct 30, 2017

By Stefan Stein, Jorge Davo, Adrian Villanueva, Abhay Kulkarni, Shane Hoff

Pellet sizing plays a key role in the productivity of the entire pelletization and subsequent induration processes, whereas uneven pellet sizing can increase the circulating load of the balling circuit inducing operational instability leading to production loses. The present work focuses in comparing the agglomeration kinetics, expressed as the number of pellets produced in a determined target size range, of different organic binder-bentonite binder systems. The batch experimental results show that the binder system has a great influence in the resulting pellet sizing, which could lead to advantages in terms of balling circuit efficiency and eventually operational de-bottlenecking.

Oct 1, 2019

By Davidson Marcos de Oliveira, Antonio Adel dos Santos, Vicente Tadeu Buono

The benefits of using the controlled rolling process followed by accelerated cooling (TMCP), currently used in the main rolling mills in the world are already well known and metallurgically based. The need to obtain mechanical properties with a high degree of homogeneity means that in some situations the ends of the rolled material are discarded, negatively affecting the metallic yield of the process. Therefore, this work focused on the determination of the mechanical properties variation at the ends of thick plates processed by TMCP of steels for application in oil and gas pipelines, in order to map the extent of these differences and to correlate them with the microstructure obtained, the profiles of temperature and cooling rates in these regions. To perform the work, two slabs of the studied material were rolled, and the temperature profile was recorded along the plate in the controlled rolling and accelerated cooling processes. The ends of the material were sampled in sections at every 100 mm and subjected to tensile test, hardness and the Charpy V-notch impact test, as well as dilatometry and microstructure evaluations. For the used process conditions, the results indicated the formation of a banded microstructure, basically consisting of polygonal ferrite and bainite, occasionally containing small fractions of perlite. The mechanical properties in the top and the base were higher than the values found in the plate middle, justified by the microstructure found. The work allowed understanding the relationship between the mechanical properties, microstructures and process conditions at the ends, helping the team to improve the process in order to result in a high degree of homogeneity of the product and, thus, lead to optimization of the metallic yield.

Oct 1, 2019

By Jens Kempken

A competitive landscape pressurizes the steel producers business, zero defect requirements from customers forces the operators for additional efforts in process control and quality management. The so called quality related cost, which include also rework, cost for downgrading or even scabbing of material is already a remarkable lever in a plants profitability breakdown. The introduction of advanced state of the art grades in the product portfolio requires already a budgeting for the expenses for R&D and quality management. PQA has been developed as a process and quality management software solution next to existing level 2 or level 3 automation systems. It is focusing on the analysis of process data, equipment information, in line quality measurement devices and trend analysis to obtain an answer whether the process is according to definition and expectation and whether the intermediate or final product can be shipped for further processing as prime material. Advanced analytics which are linked to an expert know how based configuration identifies deficiencies in the production and processing process. An intelligent, state of the art quality rating system evaluates tolerable deviations. PQA comprises the software platform including the database, data configurator and collector from the different sources in the production process and units. The core element of the platform is the knowledge based expert know how package defining process and quality determining fundamentals. The paper describes the structure of the software package, it gives insights on the expert know how package, process and quality evaluation and points out the customer benefits, cost reduction, improvement yield, customer satisfaction increase. The link to recent operational references is given.

Oct 30, 2017

By Wen Xuan

Oolitic iron ores have significant economical importance because of their extensive resources in the world. However, their utilisation is often quite limited due to the high content of phosphorus inside. The phosphorus is often finely disseminated in the oolite structure and generally not liberated in the form of free particles. The iron ore used in this work is a typical oolitic goethitic iron ore with high phosphorus. The process of phosphorus removal from this ore is difficult because the phosphorus is not present as distinct minerals. As a result, no physical beneficiation process is able to separate the phosphorus from the iron bearing phases. The current concentrate contains low iron grade (Fe ~49%) and high phosphorus content (P 0.7~0.8%). The acid leaching is a potential way to dissolve phosphorus. Previous studies have shown that the thermal treatment makes the phosphorus more accessible for the acids and enables more efficient phosphorus dissolution. Some chemical additives are reported to enhance this phenomenon. A series of tests have been carried out using roasting - grinding - magnetic separation - leaching technologies to remove the phosphorus from this current concentrate. In the first stage, several tests were performed at pilot scale under the same conditions as described in some publications. The achieved results were similar to those from previous tests at laboratory scale. In the second stage, new test conditions were investigated in laboratory scale in order to achieve better result and to reduce the operational cost.

Aug 1, 2018

By Rodrigo Fina Ferreira, Jacek Kolacz, Luciana Gois, Neymayer Pereira Lima

The recent developments on the sensor detectors together with the higher capacity of the machines, due the high-speed computing recent advances, have made possible extending the application in the mining industry. The use of x-ray fluorescence, x-ray transmission and radiometric sensor based sorting can selectively remove gangue minerals in different size fractions for different minerals. This paper summarizes the potential application of SBS for an iron ore in three size fractions aiming to increase the %Fe after the removal of particles with main gangue minerals associated. Pilot plant tests were carried out with samples of iron ore in different size fractions and different content of hematite and gangues. The use of x-ray transmission sensor showed the possibility to increase the %Fe from about 63% to above 68% for particles below 80mm and 45mm, after the removal of low density particles. The presence of fines on the feed affected the performance of the SBS X-rays transmission machine, especially for the fine fraction feed. The mineralogical determination, carried out to know the association between hematite and gangue minerals, and the density of the particles on the feed, can be used to preview the quality of products of the x-transmission sorting process.

Oct 3, 2019

By Florian Markus Penz

The increase in Basic Oxygen Furnace (BOF) plants in steelmaking has given rise to renewed interest in a dynamic simulation of the BOF process. Material and process costs can be saved with optimized process times and targeted charging of scrap and slag formers. Beside hot metal, scrap is the main source of iron in the BOF process. Furthermore, scrap is used as a coolant during the process due to exothermal chemical reactions occurring in the BOF. In this paper, the melting and dissolution behaviour of scrap in the BOF process is discussed. A new dynamic thermodynamic and kinetic Matlab® model used to simulate scrap melting behaviour as a function of various scrap surface parameters and particle size is presented, as well as the influence of scrap properties on liquid bath temperature and final crude steel composition after a defined blowing period.

Oct 30, 2017

By Jörg Schwelberger

Government regulations around the world concerning environmental care are becoming more stringent, also including regulations and restrictions of depositing and use of dust, sludge and slag generated in the iron and steelmaking process. With this scenario, by-products such as iron containing dust, sludge, oxide fines, mill scales and slag, become a valuable resource and recycling may be a profitable activity within a plant. Up to ten percent in mass of the total steel output of dust, sludge and mill scale by-product materials and more than 40% of slag by product are generated within an integrated steel plant with an iron content ranging from 50% to 65% for fines and up to 25% for BOF-slag. Slags are being widely recycled and used in the cement industry, as is the case for BF slag, and in the construction industry in the case of BOF slags and EAF slags. However, value of BOF unmodified slag is typically low and environmental regulations limit the usage of the unmodified BOF slag. This paper describes innovative solutions for recycling of fines using cold briquetting technology and the modification and granulation of slag from steelmaking that increase the value of the by-product and yield a marketable product.

Aug 16, 2017

By Nelson SOUTO, Nicolas LEGRAND, Christian COUNHAYE, Don EARLEY

The work is motivated by the automotive customer requirements for a roughness with high peak density (RPc > 75 peaks/cm) on steel sheet surfaces to maintain a good strip surface finish after painting. For that purpose, a new approach is utilized to compute roughness transfer and predict final roughness on uncoated steel sheets (average roughness, skewness, peak density) as a function of temper rolling conditions. The approach is based on the Monte Carlo method combined with the Abott curves and an auto-correlation function to numerically generate roughness profiles for roll and strip respectively. To compute the roughness transfer due to the interaction between roll and strip surfaces during rolling, a composite Abott curve that combines roll and strip Abott curves is used with an asperity crushing model integrated with a rolling model. This enables simulating two roughness transfer mechanisms in the roll bite: the strip asperity crushing mechanism by roll roughness and the strip asperity ploughing mechanism due to roll-strip interfacial sliding speed. The model shows the importance of considering the two mechanisms to predict roughness transfer correctly when strip elongation is high, typically a few percent, and roll bite friction is low. In these conditions, the forward slip at the exit of the roll bite tends to erode strip roughness significantly and decrease considerably the peak density on the strip. For lower elongation levels (~1%) and high roll bite friction, the ploughing mechanism becomes negligible and roughness transfer is controlled by the crushing mechanism only. With these two mechanisms, the model reasonably predicts the evolution of average roughness and peak density over a wide range of temper rolling conditions (new/worn work rolls, hard/soft grades, various elongations), but skewness is more difficult to predict for some trials.

Oct 1, 2019

By Alberto Tremea

The eddy current system is universally recognized as a most suitable method to point out discontinuities or modifications on the roll surface. The automation of the controls through the implementation of sophisticated equipments on the grinding machine has favoured its employment in the roll shop. A big effort is still going on to clarify the best way to promptly identify situations that could be really unsafe for the roll life. The results presented in this paper have been obtained through an intensive activity conducted in field by Innse Cilindri on work rolls of finishing stands of hot strip mills. The correct interpretation of the eddy current signals and a good calibration of the automatic system have allowed, in many cases, a substantial optimisation of regrinding practices.

Aug 16, 2017

By Marco Antonio Meggiolaro

Most cyclic plasticity models used in multiaxial fatigue life predictions are based on a concept of a yield surface, which divides the elastic and plastic domains. Plastic straining occurs when the stress state reaches the surface and tries to move outward. Subsequent plastic straining causes the stress state to remain on the yield surface, which will translate to prevent the stress point from moving outside it according to a kinematic hardening rule that models the Bauschinger effect. The accurate modeling of the yield surface shape is fundamental to predict stress-strain relations. In this work, the main yield surface equations for isotropic materials are compared. Even though most materials can be modeled using Mises and Tresca surfaces, other need to consider the effect on the yield strength of the hydrostatic stress or the normal stress acting on a critical plane. It is shown that pressure-sensitive models originally devised for concrete can be applied to predict yielding in some materials, and even fatigue life for metallic structures with short cracks.

Aug 8, 2018